sac levha çalışması kullanılmış satılık (3,292)

material width:600 mmmaterial thickness: - 4,0 mmno. of straightening rolls:21 straightening roll diameter:30 mmmaterial cross-cut:1800 mm²speed:6 - 36 m/minPower capacity:4,5 kWWeight:2,0 tDimensions (WxDxH):1,5 x 2,0 x 1,9 m

material width:70 mmmaterial thickness:0 - 1,5 mmfeed length:100 mmmaterial cross-cut:60 mm²feeding force:400 Nclamping force of feeding pincer:1300 Nair pressure - required:3 - 6 barWeight:0,01 tDimensions (WxDxH):0,4 x 0,4 x 0,7 m

sheet width:5040 mmplate thickness:2 mmtotal power requirement:12 kWweight of the machine ca.:9,4 tdimensions of the machine ca.:6200× 1300 ×1900 mmworking width:5000 mmcontrol:Fasti Matik stroke of upper beam:500 mmadjustment of lower beam:u.Biegewange 80 mmcontrol cabinet:1000 x 850 x1450 mmDocuments:vorhanden

band width:2000 mmplate thickness:1.8 mmnumber of rolls:13 Controls:SIEMENS DECOILER:. - design : single coil :. - sheet width max:2000 mm - sheet width (min):400 mm - max. weight of coil:30 to - max. diameter of coil:2000 mm - min. internal diameter of coil:610 mmFEEDERS:. - sheet width max:2000 mm - sheet thickness max:2 mm - feeding step max.:4000 mmLEVELER UNIT:. - sheet width max:2000 mm - sheet width (min):400 mm - sheet thickness max:1.8 mm - sheet thickness (min):0.6 mm - number of leveler rolls:13 - diameter of leveler rolls:50 mm

: neu : ca. 8 Wochen ab Auftragse : Spanien : 30800 €: 588.28 €: 85 to: 300 mm: 5 : 40/15 bzw. 24x24 mm: 450x15 / 450x18 mm: 475 mm: 130x130x13 mm: 45/40 mm: 12 mm: 200x12 mm: 9.2 kW: 2300 mm: 1200 mm: 2100 mm: 2400 kghydraulic drive2 foot pedals for independant working on punching and section stationbending unit with 2 dies, V40 and V70flat steel stationWITH DEVICE FOR REDUCING DEFORMATIONangle iron station with round and square bar cuttingtriangular notching station with table and gaugepunching station with table and gaugegauge 1000 mm with contact switch, for angle / flat steel stationoperating manual in German and EnglischThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 090209 : prompt, Zwischenverkauf v : Italien : 7780 €: 150.15 €: 1 : 1 : 42 mm: 400 mm: 570 mm: 1000 mm: 80 kg: 4 cm³: 42 x 3 mm: 48 x 1,5 mm: 42 x 4 mm: 42 x 2 mm: 42 x 2 mm: 50 x 3 mm: 54 x 2 mm: 54 x 2 mm: 60 x 2 mm: 50 x 4 mm: 30 mm: 40x20 (liegend), 40x12 (s mm: 260 mm: 10 mm: 3,3 U/min: 1.1 kWmanual clampingelectronic preselection of bending angledigital read our for Clamping position30 programms with each 9 bendsmaterial spring back compensationoverload protectionmobile by rolls and handlefoot pedaltools not includedAlternatively also available as following models (prices on request):MB 42M (single phase, 2 U/min) MB 42PM (portable, single phase, 2 U/min)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Italien : 32900 €: 628.39 €: 50 mm: 4000 mm: 950 mm: 1250 mm: 430 kg: 6 cm³: 50 x 3,31 mm: Ø 1”1/4 mm: Ø 50 x 2,5 mm: 40 x 40 x 4 mm: 25 x 50 x 6 mm: 50 x 25 x 2,7 mm: 60 mm: 200 mm: 20 mm: 210 °: 1,25 / 2,5 : 3.5 kW: 15 lWith mandrel 3 m lengthCan be used with or withoud mandrelTwo bending speedsProgrammable bend sequencing and mandrel retractionIndependent clamp and pressure die adjustmentMicrometer wiper die adjustmentAuxiliary system for stabilizing the hydraulic slide pressureQuick tool change systemWith pneumatic material clamping and DRO system for linear and rotational positioningALTERNATIVELY:model with mandrel 6 m length price on requestThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 8 Wochen ab Auftragse : Spanien : 22400 €: 430.08 €: 80 to: 300 mm: 5 : 40/14 bzw. 24/24 mm: 70 mm: 40 1/min: 450x15 / 300x20 mm: 130x130x13 mm: 45 mm: 12x52x90 mm: 9 kW: 2310 mm: 1200 mm: 2050 mm: 2070 kg2 foot pedals for independent work at 2 stationshydr. driveflat bar shearangle bar shear with minimum deformation by diagonal moving of the bladeround and square bar shearrectangular notching unitpunching unit up to diam. 40 mmstandard hydraulic, centring deviceoilfillingtable at the punching station with gaugetable at the notching unit with gaugetable at the flat bar shearuser manual in GERMAN and ENGLISH(sample photo shows mod. hyd 80 SD) option ",Kit", EURO 970,--length stop 1000 mm with contact switch, for angle, flat or bar stationmagnetic machine lamp10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm Fur ...

: neu : 2025 : 090054 : prompt, Zwischenverkauf v : Spanien : 17300 €: 298.94 €: 1 : 15570 €: 55 to: 250 mm: 5 : 40/10 mm: 20 mm: 37 1/min: 300x15 mm: 120x10 mm: 40 mm: 10 mm: 5 kW: 1670 mm: 1160 mm: 2090 mm: 1390 kg2 foot pedal for independent working on 2 stationsflatsteel stationanglesteel stationround- and square steel stationrectangular notching stationpunching stationtable on flat steel stationtable on punching stationtable on notching stationcomplete with hydraulic oiluser manual in GERMAN and ENGLISHOPTION:Kit € 930,00length stop 1000 mm with contact switch, for angle, flat or bar stationmagnetic machine lamp10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 5020 mm: 1.25 mm: 2 mm: 1.25 mm: 5 : 5 : 1130 mm: 180 mm: 915 mm: 3 kW: 6200 mm: 1435 mm: 1980 mm: 3000 kg: 145 °hydraulic drivestandard controladditional rail on the bending beam2x foot pedalremoveable material supportsafety equipment accoring to the control rules BG GermanyOPTIONS AS ROTARY SHEAR, CNC CONTROL, BACKGAUGES … ON REQUEST Prices ex works Germany.Transport and commissioningat customers place on request.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 1 : 6200 mm: 1.25 mm: 2 mm: 5 : 5 : 1130 mm: 180 mm: 915 mm: 3 kW: 7380 mm: 1435 mm: 1980 mm: 3200 kg: 145 °hydraulic drivestandard controladditional rail on the bending beam2x foot pedalremoveable material supportsafety equipment accoring to the control rules BG GermanyOPTIONS AS ROTARY SHEAR, CNC CONTROL, BACKGAUGES … ON REQUEST Prices ex works Germany.Transport and commissioningat customers place on request.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 6 Monate ab Auftragse : Taiwan : 52900 €: 999.81 €: 3100 mm: 4.5 mm: Hydraulisch : 135 °: 4500 mm: 1750 mm: 1950 mm: 5500 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control with 7", touchscreen incl. motorized back gauge 800 mm (sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 11800 €: 226.56 €: 2500 kg: 1300 mm: 450 - 550 mm: 400 mm: 50 mm: 80 mmmotorized drivemechanical adjustable coil mandrel with 4 jawsspeed control for decoiling speed aswell as acceleration- and deceleration timesphotoelectric proximity ensor SICK for sag controlALTERNATIVES (PRICES ON REQUEST):Version with pneumatic pressure armVersion with brake, without motor, with or withaout pneumatic pressure armThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 12100 €: 232.32 €: 2500 kg: 1300 mm: 450 mm: 550 mm: 600 mm: 50 mm: 80 mmmotorized drivemechanical adjustable coil mandrel with 4 jawsspeed control for decoiling speed aswell as acceleration- and deceleration timesphotoelectric proximity ensor SICK for sag controlALTERNATIVES (PRICES ON REQUEST):Version with pneumatic pressure armVersion with brake, without motor, with or withaout pneumatic pressure armThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 19100 €: 366.72 €: 4000 kg: 1300 mm: 450 - 550 mm: 600 mm: 50 mm: 80 mmmotorized drivemechanical adjustable coil mandrel with 4 jawsspeed control for decoiling speed aswell as acceleration- and deceleration timesphotoelectric proximity ensor SICK for sag controlALTERNATIVES (prices on request):Version with pneumatic pressure armVersion with brake, without motor, with or withaout pneumatic pressure armThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 8200 €: 158.26 €: 1250 kg: 1300 mm: 450 - 550 mm: 400 mm: 50 mm: 80 mmmotorized drivemechanical adjustable coil mandrel with 4 jawsspeed control for decoiling speed aswell as acceleration- and deceleration timesphotoelectric proximity ensor SICK for sag controlALTERNATIVES (prices on request):Version with pneumatic pressure armVersion with brake, without motor, with or withaout pneumatic pressure armThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 31620 €: 603.94 €: 0.4 - 2 mm: 600 mm: 1200 mm²: 80 mm: 75 m/min: 10 m/s²: 10 Nmhelical gear boxWATTDRIVE (Made in Austria)FESTO pneumatic equipmentservo drive and control SIEMENS7", colour touchscreen SIEMENS2 driven rollsOPTIONAL EQUIPMENTHandrwheel and Simlinx remote control € 4.290,--The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 12700 €: 243.84 €: 1270 mm: 5 mm: 140 mm: 3,5 m/min: 2.2 kW: 2470 mm: 750 mm: 1000 mm: 1350 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotormanual Back Rollforward tiltable upper rollforward and reverse revsconical bending by tilt of backrollmovable control panelusers manual in ENGLISH or GERMANOPTIONS:hardened Rolls€ 1.500,-Motorised Back Roll (Power Rear Roll)€ 1.200,-Digital Read-Out€ 1.200,-The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width:180 mmcoil weight:0,75 tmaterial thickness:2,0 - 6,0 mmcoil external diameter:400 - 1250 mmno. of straightening rolls:5 number of draw-in rolls:2 band speed:20 m/minpower requirement:4,0 kWweight:2,8 tdimensions (WxDxH):1,4 x 2,45 x 1,85 msnubber roll:pneumatic

: neu : ca. 10 Wochen ab Auftrags : Türkei : 6700 €: 129.31 €: 1550 mm: 2 mm: 90 mm: 6 m/min: 1.5 kW: 2130 mm: 700 mm: 1200 mm: 545 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotorlateral roll adjustable by handwheellongitudinal grooves in lower and lateral rolltiltable upper rollright / left rotation with double foot switchconical rolling deviceuser manual in GERMAN or ENGLISHOPTIONS:powered back roll EUR 1.000,-digital readout EUR 1.100,-The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

material width:150 mmmaterial thickness:1,5 mmpower requirement:3,0 kWno. of straightening rolls:7 straightening roll diameter:50 mmnumber of draw-in rolls:4 weight:0,67 tDimensions (WxDxH):1,3 x 1,1 x 1,6 m

: gebraucht : 2012 : 9690F : prompt, Zwischenverkauf v : China : 690 €: 1 : 100 mm: 3 mm: 90 °: 90 kgAdjustable stops on both sidesFinger guardThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. ram stroke:220 mmtotal power requirement:1,5 kWweight of the machine ca.:880 kgdimensions of the machine ca.:1.500 x 1.000 x 2.200 mmslot-milling length:220 mmtoolhead swivelling: +/- 10° ° Gradtable::650 x 250 mmtable adjustment: vertical:360 °mmtable adjustment: quer/längs: 170/400 °mmstrokes per minute:45 / 78 / 125 Hub/min feed:: 0,1 / 0,2 / 0,3 in 3 step

max. ram stroke:220 mmtotal power requirement:1,5 kWweight of the machine ca.:880 kgdimensions of the machine ca.:1.500 x 1.000 x 2.200 mmslot-milling length:220 mmtoolhead swivelling: +/- 10° ° Gradtable::650 x 250 mmtable adjustment: vertical:360 °mmtable adjustment: quer/längs: 170/400 °mmstrokes per minute:45 / 78 / 125 Hub/min feed:: 0,1 / 0,2 / 0,3 in 3 step

: neu : 2024 : 9722 : prompt, Zwischenverkauf v : Türkei : 16600 €: 318.72 €: 1 : 2050 mm: 3 mm: 130 mm: 3,5 m/min: 2.2 kW: 3200 mm: 750 mm: 1000 mm: 1500 kg3 rollsasymmetric rolls - prebending2 rolls driven by brakemotorHARDENED ROLLSmanual Back Rollforward tiltable upper rollforward and reverse revsconical bending by tilt of backrollmovable control panelusers manual in GERMANOPTIONS:(time of delivery with options approx. 8 weeks)Motorised Back Roll (Power Rear Roll) Digital Read-OutThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 6 Monate ab Auftragse : Taiwan : 57500 €: 1086.75 €: 4010 mm: 2 mm: Hydraulisch : 135 °: 5600 mm: 1750 mm: 2050 mm: 4600 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control Schneider7", touchscreen incl. motorized back gauge 800 mm (sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 6 Monate ab Auftragse : Taiwan : 61300 €: 1158.57 €: 4010 mm: 3.5 mm: Hydraulisch : 135 °: 5600 mm: 1800 mm: 2050 mm: 6100 kghydraulic drivenNC control for bending anglemanual back gauge 600 mmsharp rail 45° (in one piece)front angle beam 75 mmmechanical stop adjustment of upper beamclamping force adjustment of upper beamaccording to CE rulesALTERNATIVELY:versionAMH-K,withSECTIONEDsharp rail 45° OPTION:2 axes NC control Schneider7", touchscreen incl. motorized back gauge 800 mm(sample photos)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0143 : 690 €: 1 : 3100 mm: 90 mm: 25 mm mint durumuBu reklamın verisi, LogoTech oHG'nin yazılım çözümü olan ModulMWS ile oluşturulmuştur.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 4900 €: 109.71 €: 1050 mm: 3 mm: 2 mm: 90 mm: 2080 mm: 700 mm: 1250 mm: 410 kg3 rollsasymmetric rolls - prebending2 rolls driven by handwheellateral roll adjustable by handwheellongitudinal grooves in lower and lateral rolltiltable upper rollconical rolling deviceuser manual in GERMANThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 111500 €: 2107.35 €: 3100 mm: 20 mm: 20 mm: 16 mm: 16 mm: 12 mm: 350 mm: 350 mm: 260 mm: 1,5-5 m/min: 22 kW: 6000 mm: 2200 mm: 1900 mm: 15000 kg4 rollsfullhydraulic drive of upper roll and lower rollhydraulic infeed of lower and side rolldigital read-out of lower and side rolls positionhardened rollsconical bending devicehydraulic load relieving of upper rollhydraulic drop-end bearing2 working speedscentral lubrication systemprotectionagainst overloadmoveable control paneaccording to CE rulesOPTIONAL EQUIPMENT:infinitely adustable speed of rollshydraulic side supporthydraulic top supportNC controlIMPORTANT ISSUES AT CONICAL BENDING:the max. sheet metal thickness isequivalent to 50 % of nominal capacitythe cone length can be max. 30 % oremust be more than 60 % of roll lengthhardened rolls are recommendedThe data for this ad was created wit ...