kaynak makineleri kullanılmış satılık (1,772)

Makine tipi: MIG/MAG kaynak makinesi MERKLE yapmak RedMIG eco 2800 K yazın AB Eko-Tasarımına uygundur 2019/1784 Sayılı Yönetmelik Bağlantı gerilimi 3 x 400 volt Ayar aralığı 30 – 280 amper 280 amperde %30 ED görev döngüsü 210 amperde %60 ED 180 amperde %100 ED Akım ayarı 14 anahtarlama seviyesi Dahili fan ile soğutma transformatörü Soğutma brülörü gaz soğutmalı Mobil kompakt sistem tasarımı Tel besleme ünitesi 4 makaralı tahrik DV 26 Sigorta 16 Amper Boyutlar U x G x Y 800 x 460 x 655 mm Ağırlık 97 kg 12 aylık yaş Durum atölye tarafından test edildi, çok iyi, UVV test raporu dahil Aşağıdaki aksesuarlarla birlikte tedarik kaynak sisteminin kapsamı: 1 adet kaynak torçu 3 mtr. uzun 1 adet topraklama kablosu 1 adet basınç düşürücü 1 rulo kaynak teli D-300 bobin, 5 kg 1 ...

20 identical welding machines are available. Type: cool41 U31, standard: IEC 60974-1, -2, -10 C.L.A, mains voltage: 400V, frequency: 50/60Hz, protection class: IP23, power consumption P min: 0.9kW, cooling capacity P max: 0.35MPa (3.5bar), max. current consumption: 2.5A, length: 539mm, width: 210mm, height: 415mm, weight: 22kg. Control: Comfort 2.0 with intuitive operation via click wheel, pulse spot normal mode continuously adjustable (especially for TIG welding), pulse pause ratio (balance) adjustable for example from 10-90%, Hz and kHz pulses up to approx. 15kHz, ActivArc technology dynamic arc control to ensure constant performance despite distance fluctuations and to prevent electrode sticking, improved root and penetration quality, spotArc Spotmatic functions for spot welding and tacking, 2-stroke and 4-stroke mode depending on torch trigger operation, manual metal arc welding ofte ...

10 identical welding machines are available. Fuse protection: 32A, welding range: 40-350A, open circuit voltage: 18-43V, switch steps: 20, welding current at 100 percent duty cycle (40°C): 260A, length: 900mm, width: 560mm, height: 950mm, weight: 120kg. Standards: EN 60974-1 IEC 60974-1 international standard for arc welding equipment, protection class: IP23, protection against spray water and solid foreign objects smaller than 12mm, suitable for outdoor use, insulation class: H, cooling method: AF air cooling with fan, welding current range: 40A 16V to 350A 31.5V, open circuit voltage U₀: 18-43V, duty cycle at 350A: 50 percent duty cycle 5 minutes welding 5 minutes pause, at 330A: 60 percent duty cycle 6 minutes welding 4 minutes pause, at 260A: 100 percent duty cycle continuous operation possible, mains supply voltage: 3~400V 50Hz three phase, maximum mains current I₁ max: 25A, ef ...

3 identical welding machines are available. Very little used. Standard: EN 60974-1, three phase 3~400V 50Hz. Rated values at X 40°C: 5A 10V, 350A 24V 40 percent, 320A 22.8V 60 percent, 280A 21.2V 100 percent for one operating mode, another operating range 5A 20V with 320A 32.8V 40 percent, 290A 31.6V 60 percent and 260A 30.4V 100 percent, U1 = 400V, protection class IP23. It is an inverter controlled TIG MMA welding power source with max. 350A, digital control and memory functions, pulse function adjustable from approx. 0.5Hz to 2kHz, HF or lift ignition, adjustable parameters such as gas pre flow and post flow, slope up and down, balance and various waveforms sinus square etc., PFC technology for high efficiency and operation on generators, remote control or foot pedal connection, thermal monitoring and fault diagnosis with error codes, optional water cooling unit KG 10. An on-site ins ...

A Rehm Invertig Pro 350 AC DC and a Rehm Invertig Pro 450 DC are available, used and in good condition. 1) Invertig Pro 350 AC DC, standards: IEC 60 974-1 IEC 60 974-2, welding current range TIG: 3-350A, output voltage U₂ at maximum current: approx. 24V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent for TIG at 350A, mains voltage input: three phase 400V 50Hz, protection class: IP23S, protection category: S, setting range: 3-350A for TIG in this AC DC version, duty cycle 100 percent at 40°C 350A for TIG 100 percent duty cycle, input fuse protection: 32A at 3x400V for the 350 AC DC version, length: 520mm, width: 360mm, height: 460mm, weight: 29.5kg for AC DC version. 2) Invertig Pro 450 DC, standard: IEC 60 974-1, welding current range TIG: 3-450A, output voltage U₂ at maximum current: approx. 28V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent at 450A ...

5 identical welding machines are available. Mains voltage: 400V 50/60Hz, fuse: 25A, power consumption: 22kVA, cos phi: 0.8, setting range: 40-400A, working voltage: 16-34V, open circuit voltage: 19-55V, voltage steps: 2x12. Duty cycle at 40°C: 60 percent at 360A 32V, 100 percent at 250A 26.5V. Protection class: IP23, insulation class: H 180°C, cooling type: F. Weight gas cooled: 153kg, water cooled: 161kg. Length: 1040mm, width: 460mm, height: 935mm. Two coarse steps, 12 fine steps, high performance 4 roll wire feeder 140W, feeding speed: 0.5-24m/min, wire diameter: 0.8-1.6mm, 2 choke outputs for adjustment to the welding task. Control MC 15 as a compact easily exchangeable control box. Functions: wire feed speed constant control, wire creep, burn back time, 2 stroke and 4 stroke, wire inching without current and gas, low noise fan thermostat controlled for gas cooled units, thermal ov ...

consisting of: - Laser welding head in aluminum case - Coaxial extension - Gas pressure reducer for welding gas supply - Operating instructions - Aluminum carrying case 5300_2 - WSweld Starter Kit Starter Kit WSweld Consisting of: 3 x Annular gap nozzle 1 x Focusing mirror 1 x Deflecting mirror 1 x ZnSe window Laser welding head TC08 Replacing the cutting head with the WSweld laser welding head TC08 expands a flatbed machine into a laser welding system. Deep penetration and heat conduction welding combined in one optic Active cooling of all optical elements Coaxial welding gas supply for perfect laser weld seams Cross-jet prevents contamination of the optics Active collision detection The WSweld laser welding head TC08 is compatible with the following machine types: TRUMPF TruLaser 3030 classic TRUMPF TruLaser 5030 classic TRUMPF Trumatic L2530 TRUMPF Trumatic L3030 TRUMPF Trumatic L3040 ...

Ürün Kodu: BAS 051. Şerit testere bıçakları için otomatik flaş alın kaynak makinesi. Pnömatik sıkıştırma. Tavlama pirometresi. Bıçak konumlandırma için yerleştirme çubuğu. UniOp otomatik tavlama sıcaklık kontrolü. Makine temizlendi ve yeniden boyandı. Üretim yılı: 2001. Nominal birincil voltaj: 380 [V AC]. kaynak derecesi: 8 [kVA]. Sıkıştırma kuvveti: 20 [kN]. Dövme kuvveti: 5 [kN]. Kaynak aralıkları. Ahşap için şerit testere bıçakları: 6-50 [mm]. Bi-metal şerit testere: 6-41 [mm]. Çember bıçakları: 6-50 [mm]. Paslanmaz çelik şerit testere: 6-30 [mm]. Ağırlık: 600 [kg]. Boyutlar (GDY): 135010001700 [mm]. Talimatlar ve paketleme dahildir.

Kullanılmış kaynak ekipmanı Resimlerde görüldüğü gibi, teknik veriler Resimlere bakın. Başka sorularınız varsa, lütfen Fiyat parça başınadır

Ref.nr. 00886 Sistemin adı: Portal örgü kaynak makinesi Üretici Fibro GSA Almanya'da üretilmiştir GAE 516 Modeli Yapım yılı 2008 Tabela: Bağlı yük 630 kVA Birincil voltaj 400V Nominal frekans 50-60 Hz Sigorta 800A Özellikler: Nominal birincil gerilim 400V/ 50 Hz Kontrol gerilimi 24 V/DC Transformatör sayısı 10 adet %50 ED'de trafo başına nominal güç 63 kVA %50 ED'de bağlı yük 630 kVA Sigorta L1+L2+L3 (Lmax 90m) 800 A Besleme kablosu kesiti L1 + L2 + L3 (Lmax 90m) 2x240 mm2 PE 1x240mm2 makineye besleme hattı Besleme kablosu PC 230V 10A 3x2,5 mm2 Elektrot kuvveti 480 N/bar Hava basıncı – bağlantı G 3/4 Hava basıncı min. 6 bar 80 devir / dak'da hava tüketimi 600 Nl / dak Soğutma suyu bağlantı girişi G 2.0 Soğutma suyu bağlantı çıkışı G 2.0 Soğutma suyu tüketimi 92 l/dak Soğutma suyu basıncı min. 3 çu ...

Ref.Nr. 00885 Sistemin adı Hasır kaynak makinesi CE Üretici: IDEAL Werk - Lippstadt İDEAL 05 küçük GAE 112 Modeli Üretim yılı 2004 2021'de revize edildi. Diyot paketi ve transformatörler değiştirildi, 32.000 € değerinde kablolar temizlendi Aktivite / Açıklama – Punta kaynağı yarı otomatik %50 ED'de nominal güç 2x200kVA Bağlı yük 400kVA Birincil voltaj 400V Açık devre gerilimi 7V Nominal frekans 50-60 Hz Sigorta 800 A Almanya'da üretilmiştir Özellikler: Nominal birincil gerilim 400 / 50 V / Hz Kontrol gerilimi 24 V/DC Transformatör sayısı 2 adet %50 ED'de trafo başına nominal güç 200 kVA %50 ED'de bağlı yük 400 kVA Sigorta L1+L2 800 Amp Sigorta L3 63 Amp Besleme kablosu kesiti L1 + L2 + L3 (Lmax 90m) 2 x 240 mm2 Besleme kablosu kesiti L3 125mm2 PE 240mm2 makinesine besleme hattı Besleme kablosu PC 23 ...

container turning device, welding turning device, welding turning device, welding device, welding turntable, welding turntable and tilting table, welding turning device, welding turntable tilting table -Handover: in current condition as viewed -Condition: without drive motors / control, see photos -Welding rotating device: pivoting -Turntable: Ø 700 mm -Projection: 930 mm -Transport dimensions: 1240/730/H1640 mm -Weight: 643 kg

Lazer gücü: 4kW, çalışma alanı X/Y/Z: 4000mm/2000mm/115mm, maks.sac kalınlığı yumuşak çelik/paslanmaz çelik/alüminyum: 20mm/15mm/10mm, maks.iş parçası ağırlığı: 1700kg. Makine boyutları X/Y/Z: yaklaşık 11600 mm/5300 mm/2200 mm, ağırlık: yaklaşık 15000 kg. Trumpf Liftmaster'ı içerir. Belgeler mevcut. Yerinde inceleme mümkündür.

Özellikler: Prosedür: 2 aşamalı Filtre alanı: yaklaşık 17 m² Ayırma verimliliği: %>99 Kaynak Dumanı Ayırma Sınıfı: W3 Ekstraksiyon kapasitesi: 1100 m³/h Ekstraksiyon kolunun çapı: 150 mm Ekstraksiyon kolunun uzunluğu: 3 m Güç bağlantısı: 3 x 400 V Motor gücü: 1,1 kW Ses basıncı seviyesi: 70 dB(A) Boyutlar, yaklaşık: 785 x 730 x 950 mm Ağırlık, yaklaşık: 106 kg Özellik -lerini: - Almanya'da üretilmiştir - Düşük ila orta duman/toz miktarları için - Ara sıra ve sık kullanım için uygundur - Bakım kapağından rahat filtre değişimi - Davlumbaz döndürülebilir ve 360 derece döndürülebilir Ekipman: - 3 yeni yedek ana filtre (orijinal fiyatı yaklaşık 330 Euro) - 7 yeni yedek ön filtre - 2 adet davlumbaz (biri kullanılmamış)

Seyahat yolu X / Y / Z: 3000mm / 1500mm / 115mm, lazer gücü: 5000W, kesme kapasitesi yumuşak çelik / paslanmaz çelik / alüminyum: 25mm / 20mm / 12mm, seyahat hızı: 200m / dak, kesme hassasiyeti: 0.1mm. Makine boyutları X / Y / Z: 11000mm / 4600mm / 2400mm, ağırlık: 12000kg, kontrol: Siemens Sinumerik 840D. Konveyörleri, çeşitli lens boyutlarına sahip lazer kesim kafalarını, Liftmaster R'yi ve diğer çevresel ekipmanları içerir. Belgeler mevcut. Yerinde inceleme mümkündür.

Remote control for inert gas welding device, inert gas device, welding rectifier, hand controller-Manufacturer: Fronius, remote control RCU5000i Univ.SD-Art.No.: 4,046,098-Voltage: U1 24 V-Dimensions: 180/260/H50 mm-Weight: 1.5 kg

Çevresel ekipman dahil olmak üzere eksiksiz bir plazma kesme sistemi Oerlikon mevcuttur. 1) CNC plazma kesme sistemi Oxytome 30, üretim yılı: 2008. 2) Plazma kaynağı Air Liquide Nertajet HP125, üretim yılı: 2008. 3) Filtre ünitesi Donaldson Torit DCE DFPRO 8-Cyclo, üretim yılı: 2008, ağırlık: yaklaşık 1625kg. 4) Soğutma ünitesi Air Liquide Friojet-30, üretim yılı: 2008, soğutma kapasitesi: 2kW, maks. çalışma basıncı: 29.5bar, soğutucu: R407c, ağırlık: 80kg. Belgeler mevcut. Yerinde inceleme mümkündür.

table diameter: 340 mmtable load: 160 horizontal kg.table load: 100 vertikal kg.swivelling range: 0 - 90 Gradturning speeds: 0,6 - 6,0 U/minbore: 60,0 mmmotor: 230 Voltweight of the machine ca.: 56 kg.range L-W-H: 385 x 340 x 375 mmFurnishing:- The table can be adjusted at an angle of 0 to 90 degrees tilt and jam- Start / stop via a location-independent foot switch.- Direction of rotation can be selected right / left.- Adjustable rotation time- The turntable has a 60 mm hollow shaft- The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter.- The table speed is adjustable from 0.6 - 6 rpm.- The control of the welding machine via the turntable control is possible.- The ground contact transmits 300 A / 100%.- The turntable and the control are separate.- HF protected.- COM 1800 control with lap welding- Operating instructions in GermanFu ...

total power requirement: 230 Volttable diameter: 300 mmtable load: 100 Horizontal kgswivelling range: 0 - 90 Gradturning speeds: 0,2 - 2,0 U/minturning speeds: 1,2 - 12,0 U/minbore: 20,0 mmweight of the machine ca.: 50 kgdimensions of the machine ca.: 480 x 325 x 470 mmFurnishing:- Precise drive unit with face plate, on a stable floor stand.- clockwise / counterclockwise- 2 speed series, stepless- Swivel range from 0 ° - 90 °. Manual tilt- DC gear motor with worm gear, infinitely variable.- diameter of 300 mm. Chrome-plated surface to protect against weld spatter.- The devices control panel is easy to understand and use.- Start / stop via a location-independent foot switch.- The speed and direction of rotation are set on the machine.- HF protected.Scope of delivery:- control (integrated)- foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting range for steel to: 12.0 TS mmcutting range for steel to: 8.0 QS mmcapacity at 100%: 30.0 Amperecutting medium: Druckluft output: von 20 - 40 Ampereoutput: Eingang 4.9 KWvoltage: 230 Vweight: 17,9 kgrange L-W-H: 480 x 210 x 340 mmThe Avalon 40.1 is a light, handy plasma cutting system with highCutting performance and top cutting quality. Their light weight and simplicityHandling makes them the ideal candidate for crafts, workshops andIndustry. Cuts carbon steel, stainless steel, aluminum, copper...Characteristics- IGBT technology- Active PFC technology for high duty cycle and energy efficiency- Manual switch to activate airflow to test air pressure. without having to trigger the burner.- Powerful compact system- Intelligent protection function protects the plasma torch from damage such as incorrect air pressure, missing wearing parts, overloading of the. pilot arcmax. separation  ...

cutting range for steel to: 15.0 TS mmcutting range for steel to: 10.0 QS mmcapacity at 100%: 25.0 Amperecutting medium: Druckluft output: von 20 - 40 Amperevoltage: 230 VAir consumption: 230 l/min.output: Eingang 4.9 KWweight: 8.0 kgrange L-W-H: 505 x 147 x 305 mmThe Avalon 40.1 is a light, handy plasma cutting system with highCutting performance and top cutting quality. Their light weight and simplicityHandling makes them the ideal candidate for crafts, workshops andIndustry. Cuts carbon steel, stainless steel, aluminum, copper...Characteristics- IGBT technology- Active PFC technology for high duty cycle and energy efficiency- Manual switch to activate airflow to test air pressure. without having to trigger the burner.- Powerful compact system- Intelligent protection function protects the plasma torch from damage such as incorrect air pressure, missing wearing parts, overloading of the ...

Cutting nozzle, welding torch, heating nozzle, hand arc - piercing torch, gouging torch, gouging nozzle, burner nozzles, cutting nozzles, flame cutting system, burner, oxy-fuel cutting system -Heating nozzles: 49 pieces different sizes Ovp -Type/Quantity: see photos / parts list -Cutting range: mm -Price/Delivery: complete -Transport dimensions: 200/200/H50 mm -Weight: 1.1 kg

table length: 3000 mmtable width: 1500 mmtable height: 850 mmside-clamping surface:: 200 (Höhe) mmweight: 1517 kg SIEGMUND authorized dealer - all items available! Product description- high quality steel S355J2 + N + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Hole Ø 28 mm- Drilling surface 100x100 mm grid- Rounded corners, edges and holes- Height of side wall 200 mm- Distance between holes in side wall 50 mm- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityFurnishing:- 28 hole pattern / dimensions 3000 x 1500 x 200 mm- Plasma nitrided version with scale- incl. 6x base equipment The data for this ad was created with ModulMWS - th ...

table length: 1500 mmtable width: 1000 mmtable height (lateral area): 100 mmweight: 255 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 11.5 - 13 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 16 mm- Holes surface 50x50 mm grid- Rounded corners, edges and holes- Height of side wall 100 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityFurnishing:- 16 hole pattern / dimensions 1500 x 1000 x 100 mm- Extreme plasma nitrided version with scale- Sidewall with diagon ...

table length: 3000 mmtable width: 1500 mmtable height (lateral area): 200 mmweight: 1374 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 28 mm- Surface holes in a diagonal grid- Rounded corners, edges and holes- Height of side wall 200 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityFurnishing:- 28 hole pattern / dimensions 3000 x 1500 x 200 mm- Extreme plasma nitrided version with scale- with diagonal  ...

table length: 2000 mmtable width: 1000 mmtable height (lateral area): 200 mmweight: 699 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 24.5 - 27 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 28 mm- Surface holes in a diagonal grid- Rounded corners, edges and holes- Height of side wall 200 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityEquipment:- 28 hole pattern / dimensions 2000 x 1000 x 200 mm- Extreme plasma nitrided version with scale- with diagonal gr ...

table length: 2400 mmtable width: 1200 mmtable height (lateral area): 100 mmweight: 499 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 11.5 - 13 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 16 mm- Holes surface 50x50 mm grid- Rounded corners, edges and holes- Height of side wall 100 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structures.The welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityEquipment:- 16 hole pattern / dimensions 2400 x 1200 x 100 mm- Extreme plasma nitrided version with scale- Sidewall with diagon ...

table length: 2000 mmtable width: 1000 mmtable height (lateral area): 100 mmweight: 351 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 11.5 - 13 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 16 mm- Holes surface 50x50 mm grid- Rounded corners, edges and holes- Height of side wall 100 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityEquipment:- 16 hole pattern / dimensions 2000 x 1000 x 100 mm- Extreme plasma nitrided version with scale- Sidewall with diagona ...

table length: 3000 mmtable width: 1500 mmtable height (lateral area): 100 mmweight: 753 kg SIEGMUND authorized dealer - all items available! Product description- Through hardened tool steel X8.7 + plasma nitriding- Material thickness approx. 11.5 - 13 mm- Sidewall made of high quality steel S355J2 + N + plasma nitriding- Hole Ø 16 mm- Holes surface 50x50 mm grid- Rounded corners, edges and holes- Height of side wall 100 mm- Drill holes in the side wall in a diagonal grid- Including scaling on the surface- Construction reinforced by ribs- Grid lines enable precise structuresThe welding tables are provided with a scale as standard.Plasma nitrided version:- Protection against rust / scratches / weld spatter adhesion- more corrosion-resistant / higher load capacityEquipment:- 16 hole pattern / dimensions 3000 x 1500 x 100 mm- Extreme plasma nitrided version with scale- Sidewall with diagona ...

weight max. in kg: 1250 kgturning speeds: 2,0 U/minheight: max. 1.120 mmTorque: Tisch 490 Nmweight: 685 kgThe Siegmund Roto-Positioner is ideal for welding,Assembly and maintenance work. The positioning takes place via a hydraulic oneTurn and tilt function. The Siegmund Roto-Positioner is also includedequipped with a continuously height-adjustable axis.Furnishing:- Hydraulic rotation of the clamping plate- Tilt range up to 95 °- Hydraulic height adjustment and tilt function- including hand controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.