ak bend sac levha çalışması kullanılmış satılık

sheet width: 1050 mm plate thickness: 1 mm roll diameter: 56 mm dimensions of the machine ca.: 1600 x 700 x 1050 mm Domestic equipments: - Upper roller can be swung out manually The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 13 mm pre-bending: 10 mm upper roll diameter: 230 mm lower roll diameter: 210 mm side roll diameter: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4.620 kg dimensions of the machine ca.: 4150x1400x1300 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG ...

sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1550 mm plate thickness: 4,5 mm pre-bending: 4,0 mm roll length: 1550 mm min. dia.: 190 mm roll diam. toproll: 130 mm weight: 1265 kg dimensions: 2670x1110x1050 mm Domestic equipments: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - induction hardened rolls - motorized rear roller adjustment - Digital display for back roller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 16,0 mm ST pre-bending: 20,0 mm ST diameter of upper rolls: 360 mm side roll diameter: 250 mm diameter of lower rolls: 330 mm total power requirement: 15,0 kW weight of the machine ca.: 13.200 kg. dimensions of the machine ca.: 5542 x 2100 x 1983 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with Mod ...

sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll length: 1050 mm roll diameter: 90,0 mm min. dia.: 130,0 mm engine output: 1,1 kW weight: 570 kg range L-W-H: 1.800 x 800 x 1.130 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of LogoTech ...

sheet width: 1250 mm plate thickness: 5.5 mm pre-bending: 5.0 mm roll diam. toproll: 140 mm min. dia.: 210 mm turning speeds: 5.7 U/min engine output: 2.2 kW weight: 1365 kg range L-W-H: 2020 x 900 x 1.200 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of L ...

sheet width: 4100 mm plate thickness: 13,0 mm ST pre-bending: 10,0 mm ST diameter of upper rolls: 360 mm side roll diameter: 250 mm diameter of lower rolls: 330 mm total power requirement: 11,0 kW weight of the machine ca.: 16.000 kg. dimensions of the machine ca.: 6542 x 1677 x 1900 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with Mod ...

sheet width: 2050 mm plate thickness: 4,5 mm max. plate thickness: 4,0 mm anbiegen roll length: 2050 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1530 kg range L-W-H: 3220 x 1200 x 900 mm Furnishing: - Robust electro-mechanical bending machine - 2x central rollers driven by an electric motor (top and bottom roller) - Top roller can be swiveled out manually, with folding bearing - including conical bending device - freely movable control panel - Lower roller manually adjustable, by hand wheel - asymmetrical roller arrangement - self-braking main motor - Safety device (safety line with switch unit) - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized side roller adjustment - Digital position display for motor-driven adjustable side roller The data for this ad was created with ModulMWS - the software solution of LogoTech oH ...

sheet width: 3100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 230 mm side roll diameter: 210 mm diameter of lower rolls: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 6.020 kg. dimensions of the machine ca.: 5142 x 1390 x 1300 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...

sheet width: 4100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 7,5 kW weight of the machine ca.: 9.930 kg. dimensions of the machine ca.: 6532 x 1730 x 1489 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...

sheet width: 2100 mm plate thickness: 8,0 mm ST pre-bending: 6,0 mm ST diameter of upper rolls: 190 mm side roll diameter: 150 mm diameter of lower rolls: 170 mm total power requirement: 3,0 kW weight of the machine ca.: 3.290 kg. dimensions of the machine ca.: 4042 x 1380 x 1254 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMW ...

sheet width: 1600 mm plate thickness: 15,0 mm ST pre-bending: 13,0 mm ST diameter of upper rolls: 230 mm side roll diameter: 210 mm diameter of lower rolls: 190 mm total power requirement: 7,5 kW weight of the machine ca.: 4225 kg. dimensions of the machine ca.: 4000 x 1300 x 1440 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulM ...

working length: 2050 mm : 2.0 mm max. wire thickness: 3.0 mm Underfloor: 110 mm motor strength: 165 mm motor strength: 22 kW bending speed: 5.2 mm/min length: 3150 mm height: 1150 mm width: 850 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2050 mm plate thickness: 4,5 mm pre-bending: 4,0 mm min. dia.: 210 mm roll diameter: 140 mm weight of the machine ca.: 1530 kg dimensions of the machine ca.: 3220x1200x900 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 960 mm table load: 3.500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M20 Tilt Angle: 70-90-180 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 1.500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 1,25 mm roll-body distance: 250 mm throat: 260 mm distance between roll centers: 62 mm tool adaptor: 26 mm speed: 6,3 m/min total power requirement: 0,7 kW weight: 170 kg range L-W-H: 1020x600x1500 mm Domestic equipments: - motor driven beading machine - 5 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5+0,55 kW weight of the machine ca.: 320 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 200 mm min. bending diameter: Ø 300 mm bending speed: 5 m/min total power requirement: 5,5 kW weight of the machine ca.: 4.000 kg dimensions of the machine ca.: 4800x1300x1270 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4100 mm plate thickness: 35 mm pre-bending: 28 mm upper roll diameter: 540 mm lower roll diameter: 541 mm side roll diameter: 440 mm total power requirement: 37 kW weight of the machine ca.: 48.100 kg Machine dimensions approx.: 7670x3000x2930 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 295 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 132 mm tool adaptor: 40 mm speed: 5 m/min total power requirement: 2,2 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 1650x700x1280 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1300 mm table load: 7.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 0,9 UpM T-slots: 6 x M24 Tilt Angle: 90-180-100 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 3.050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 8 mm pre-bending: 6 mm upper roll diameter: 190 mm lower roll diameter: 170 mm side roll diameter: 150 mm total power requirement: 3 kW weight of the machine ca.: 3.450 kg Machine dimensions approx.: 4040x1380x1255 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 25 mm pre-bending: 20 mm upper roll diameter: 390 mm lower roll diameter: 360 mm side roll diameter: 300 mm total power requirement: 18,5 kW weight of the machine ca.: 17.100 kg Machine dimensions approx.: 5800x2100x2000 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ...

plate thickness: 4 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 132 mm tool adaptor: 40 mm speed: 5 m/min total power requirement: 2,2+0,55 kW weight of the machine ca.: 450 kg dimensions of the machine ca.: 1800x700x1600 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 715 mm table load: 500 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-110 ° Tilting Speed: 30 sn min./90° weight of the machine ca.: 675 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 10 mm pre-bending: 8 mm upper roll diameter: 270 mm lower roll diameter: 250 mm side roll diameter: 210 mm total power requirement: 11 kW weight of the machine ca.: 7750 kg Overall size: 5600x1450x1600 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 210 mm lower roll diameter: 190 mm side roll diameter: 170 mm total power requirement: 7,5 kW Overall size: 5200x1400x1300 mm machine weight ab.: 5.400 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 6 mm pre-bending: 4 mm upper roll diameter: 160 mm lower roll diameter: 140 mm side roll diameter: 120 mm total power requirement: 2,2 kW Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according  ...

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 170 mm min. bending diameter: Ø 255 mm bending speed: 4,5 m/min total power requirement: 4 kW weight of the machine ca.: 2300 kg dimensions of the machine ca.: 3800x1100x1130 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 16 mm pre-bending: 13 mm upper roll diameter: 330 mm lower roll diameter: 300 mm side roll diameter: 240 mm total power requirement: 11 kW Overall size: 5600x1650x1900 mm weight of the machine ca.: 10.600 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1050 mm plate thickness: 1,8 mm pre-bending: 1,5 upper roll diameter: 70 mm min. dia.: 105 mm total power requirement: 1,1 kW weight of the machine ca.: 320 kg dimensions of the machine ca.: 1700x700x1100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 40 mm pre-bending: 30 mm upper roll diameter: 390 mm lower roll diameter: 360 mm side roll diameter: 300 mm total power requirement: 22 kW machine weight ab.: 17200 kg Overall size: 5060 x 2200 x 2180 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 1050 mm : 5,5 mm : 5,0 mm roll diameter: 130 / 195 mm : 2,2 kW : 1050 kg : 2150 x 900 x 1200 mm - 2 central rollers driven by an electric motor - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - upend: 100 x 20 (d 2100) mm bar material dia. max.: 100 x 3 (d 3000) mm L-beam: 80x80x8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm I - beam section - flat steel: 120 x 30 (d 600) max.140b mm bar material - diameter: 60.0 (d 1000) mm tool taper: 80.0 mm oil volume: 100 Liter turning speeds: 4.2 m/min. weight: 1600 kg range L-W-H: 1240 x 1375 x 1540 mm Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x hydraulically adjustable side guides - ...

L-beam: 40 x 5.0 (d 500) mm I - beam section - flat steel: 80 x 15 (d 700) mm I-beam section - upend: 50 x 10 (d 800) mm round material: 30.0 (d 700) mm bar material dia. max.: 60 x 2 (d 1200) mm square material: 50 x 30 x 3 mm range L-W-H: 670 x 530 x 1350 mm weight: 185 kg total power requirement: 0.75 kW Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - horizontal and vertical work possible Machine head can be folded 90° - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conformity - Operating instructions in German The data for this ad was crea ...

I - beam section - flat steel: 120 x 15 (d 750) mm I-beam section - upend: 60 x 10 (d 800) mm L-beam: 50 x 5 (d 1200) mm round material: 35,0 (d 800) mm bar material dia. max.: 70 x 2 (d 1200) mm square material: 50 x 40 x 3 mm bending speed: 4,3 m/min roll diam. toproll: 155 mm bore: 50,0 mm total power requirement: 1,5 kW weight: 320 kg range L-W-H: 730 x 830 x 1350 mm Exhibition machine from 2023 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - machine base frame, with rear shelf - horizontal and vertical work possible - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conform ...

plate thickness: 2.5 mm throat: 260 mm distance between roll centers: 92.0 mm weight: 295 kg range L-W-H: 1200 x 700 x 1200 mm Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - 3x pairs of beading and flanging rollers included in delivery - robust beading machine with motor-driven rollers - Lower shaft with adjustable stop - for the economical production of a wide variety of bead types - high accuracy thanks to precision-mounted shafts - Clearly arranged switching elements - Base frame equipped with storage compartment - powerful drive motor, even under continuous load - mobile foot switch for clockwise and counterclockwise rotation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4.0 mm throat: 260 mm distance between roll centers: 132 mm stroke: 55.0 OW mm tool adaptor: Ø 35 mm, 12 mm Nut mm total power requirement: 3.0 kW weight of the machine ca.: 450 kg. range L-W-H: 1600 x 900 x 1200 mm Exhibition machine from 2022 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - 3x pairs of beading and flanging rollers included in delivery - robust beading machine with motor-driven rollers - hydraulic adjustment of the upper roller, with pressure gauge - Lower shaft with adjustable stop - for the economical production of a wide variety of bead types - high accuracy thanks to precision-mounted shafts - Clearly arranged switching elements - Base frame equipped with storage compartment - powerful drive motor, even under continuous load - mobile foot switch for clockwise and counterclockwise rotation The data fo ...

weight max. in kg: max. 1000 kg turning speeds: 0,18 - 0,58 U/min height: 976 - 1436 mm inclination: 0 - 115 ° table diameter: 895 mm voltage: 380 V total power requirement: 2,0 kW weight: 685 kg range L-W-H: 2414 x 920 x 1436 mm Exhibition machine from 2024 with only approx. 2x operating hours Condition NEW Special price on request The AK BEND SRH hydraulic welding positioner is ideal for welding, assembly and maintenance work. Positioning is done via a hydraulic rotation and tilting function. Description: - electro-hydraulic turning and tilting function - Fast handling of workpieces - Maximum productivity thanks to optimal working position - Lifting, tilting and turning workpieces in one clamping - Low idle times thanks to turning components - Maximum work performance thanks to comfortable working - Back-friendly working for the user Equipment: - Continuously variable speed adjust ...

I - beam section - flat steel: 80 x 20 (d 1200) mm I-beam section - upend: 80 x 25 (d 2100) mm L-beam: 50 x 50 x 6 (d 1000) mm bar material - diameter: 40.0 (d 800) mm square material: 60x60x3 ( d 4000 ) mm rectangle: 80x30x3 ( d 6000 ) mm roll surface width: 177x60 (18x5 Nut) mm bar material dia. max.: 70 x 2.0 (d 1600) mm tool adaptor: 60.0 mm turning speeds: 6.4 m/min. oil volume: 80.0 Liter total power requirement: 4.75 kW weight: 1080 kg range L-W-H: 940 x 1260 x 1390 mm Exhibition machine from 2022 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscree ...

I - beam section - flat steel: 80 x 16 (d 1200) mm I-beam section - upend: 50 x 15 (d 1000) mm L-beam: 50 x 5 (d 1200) mm round material: 40.0 (d 800) mm bar material dia. max.: 70 x 2.0 (d 1600 ) mm square material: 80x30x3 (d 4000) mm channels - flange: UNP 80 (d 800 ) mm bending speed: 4.4 m/min roll diam. toproll: 157 mm bore: 50.0 mm oil volume: 18.0 Liter total power requirement: 1.1 kW weight: 485 kg Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x manual ...

sheet width: 2600 mm plate thickness: 10,0 mm pre-bending: 8,0 mm diameter of upper rolls: 230 mm side roll diameter: 190 mm diameter of lower rolls: 210 mm total power requirement: 7,5 kW weight of the machine ca.: 5.560 kg. range L-W-H: 4.650x1.380x1.300 mm Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solutio ...

sheet width: 3100 mm plate thickness: 13,0 mm pre-bending: 10,0 mm diameter of upper rolls: 300 mm side roll diameter: 210 mm diameter of lower rolls: 270 mm total power requirement: 11,0 kW Furnishing: - electro-hydraulic 4-roller bending machine - 2x driven main rollers (upper & lower roller) - with hydraulic conical bending device - Induction hardened rollers - including straightening function for welded pipes - Control unit / display with touch screen function digital position display for the two side rollers - mobile control panel - 2x bending speeds selectable - hydraulic folding bearing - Safety device (safety line with switch unit) - Pressure gauge / pressure indicator for the rollers - CE mark + declaration of conformity - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I-beam section - upend: 120 x 25 (d 1600) mm bar material dia. max.: 140 x 3 (d 3000) mm L-beam: 100x100x10 (d 1600) mm square material: 140 x 40 x 3 (d 4000) mm I - beam section - flat steel: 200 x 35 (d 1000) mm bar material - diameter: 70,0 (d 800) mm tool taper: 100,0 mm 0: 315 mm turning speeds: 5,4 m/min. total power requirement: 11,0 kW weight: 2.240 kg range L-W-H: 1500 x 1650 x 2100 mm Furnishing: - electro-hydraulic ring/profile bending machine - Hydraulic lower/side roller adjustment for extra small bending radii - Lower/side roller can be delivered individually - 3x powered rollers - divided roller segments - Digital position display of the bottom/side rollers Display with TouchScree function - hardened tool holder (42CrMo4) - Machine base - 2x hydraulically adjustable side guides - Horizontal and vertical work possible - freely movable control panel - Pressure gauge / pres ...

- Adjustable stroke with digital read out positioning display - Variabel instelbare druk - Snel wissel gereedschap systeem

: 2100 mm : 7 mm : 6 mm roll diameter: 190 mm min. dia.: 285 mm : 4 kW : 3200 kg : 4000x1350x1500 mm Equipment: - motorized rear roller adjustment - Digital display - Automatic conical bending. - Foot switch - Safety devices The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 900 mm table load: 1.000 kg Frontal Loading Center (A): 150 mm Side Loading Center (B): 150 mm Rotating speeds: 0,1 - 1,1 UpM T-slots: 6 x M16 Tilt Angle: 90-180-105 ° Tilting Speed: 30 sn min./90° dimensions: 2100x920x1100 mm weight of the machine ca.: 930 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

guillotine shears AG TS 2 Working thickness 2mm Adjustable stop Hold Length 1.80 m Width 1 m Height 1.40 m Weight 300 kg

Line Salvagnini S4 P4 Year 2001/2003 S4 30 + P4 2220 + MD with unloading robot. Working line, regular assistance performed by the manufacturer

Hydraulic Shear HACO HS 3010 Capacity: 3000 x 10 mm Back gear gauge travel: 1000 mm Year of construction: 1983 Manual adjustment of the clearance between blades Cutting angle: 1° to 3° Voltage: 380 V Dimensions (L x W x H): 4000 x 2100 x 2200 mm Weight: approx 8 T

Mechanical Shear BOMBLED type 9G Capacity: 2500 mm x 4 mm Manual Back gear gauge travel: 500 mm Supplied with 2 front length stops Voltage: 380 V Dimensions (L x W x H): 4000 x 1500 x 1500 mm Weight: approx 4,5 T

Inv. Num. : 8739 Type: TS 3006 Producer: HACO Created: 2004 Parameters: Maximum cutting length: 3000 mm Maximum cutting thickness: 6 mm

Inv. Num. : 8740 Type: VR 13-31 Producer: EHT Generated: Parameters: Maximum cutting length: 3100 mm Maximum cutting thickness: 13 mm

older Gebr. Lever shears on base frame Technical data Knife length 500 mm Cutting range approx. 3-4 mm Dimensions 800 x 170 x 1300 mm dto. incl. base frame 1300 x 600 x 1780 mm Remarks / Accessories: Underframe, small damage to the knife Maschinenladen Oeben GmbH Krahnendonk 116 D-41066 Mönchengladbach Phone: + 49 2161 662701 maschinenladen.de InfoMachine Shop

Hand lever scissors, mounted on concrete base, see pictures Sheet width - max. 200 mm Sheet thickness 6 mm Jxdh33 Flat steel 70 x 7 mm Round steel 13 mm

Year 1996, CE norm, complete instructions, control Delem, machine in TOP condition with warranty, more details on request

specifications: Max sheet width 3,000 mm Max sheet thickness at max yield strength 240 N/mm2 when bending to max. sheet width 35 mm when rounding Bend length 2.2 x S Max passage between rollers 145 mm Roller diameter upper roller 552 mm Underroller 532.4 mm Side rollers 400 mm Number of rollers 4 Powered rollers 2 top and bottom roller Drive of the rollers hydraulically Arrangement of the rollers symmetrically Rotation speed of the rollers 2-4 m/min Adjustable rollers 3 Type of adjustment of the rollers hydraulically Adjustment speed lower roller 0-200 mm/min. Side rollers 0-700 mm/min. Brake of the rollers pneumatic Actuation of the folding bearing hydraulically Operating voltage 3 x 380 V / 50 Hz Display device of the roll positions 4 x optical/analog Weight of the machine approx. 42 to Area 2.71 x 6.4 m Height 3.12 m

Key data: 300 , 4

Bandwidth - up to 460 mm Band thickness - 0,5-4 mm Motor drive - 6 kW together with Reel 1.5 T - non-powered

Capacity , ton: 800 Stroke, mm: 320 Strokes/min: 20 Shut height, mm: 900 Bed to ram adjustment stroke, mm: 320 Bed dimensions, mm: 2500x1600 Main drive motor power, kW: 75 Overall dimensions, mm: 4220x3500x8356 Weight, ton: 96,6

lechrichter, used,       sheet leveller, used,   Type: UBR 10 x 2000 /1-16 Manufacturer / make: WMW Gotha max. sheet width: 2000 mm max. sheet thickness ( St 50): 10 mm    min. sheet thickness / min. sheethickness: 3 mm   Number of straightening rollers: 13 rollers / rollers Directionroller Diameter/diameter of     straihgtening rollers: 145 mm Directional speed / speed of straightening: 16 m / min Bale length / convexity length of rollers: 2330 mm Center distance of directional rollers/ distance b/n rollers centers: 150 mm Support roller diameter / diameter of bottom rollers: 290 mm Number of bottom rollers 21/24 Number of supports (top/bottom): 3 /3 Lifting speed of the traverse / speed   ...

NC - controlled mechanical sheet metal panel scissors in backdrop cutting design, maximum cutting length 1,050 mm, maximum cutting capacity 4 mm steel sheet/ST40, cutting angle 1.5°, NC - controlled rear stop with 1,000 mm travel range - automatic removal of the stop rail at sections lower than 1,000 mm - optionally available with a foldable sheet support at the rear stop or a conveyor belt with upliftrs, drive power 5 kW, weight approx. 2,500 kg

Qty. 1 Second-hand strip rolling mill Mfc.: United Engineering Type: 4-Hi Built: Strip Width: 393 mm (15.5”) Thickness Entry: 4 mm (0.16”) Exit: 1.2 mm (0.05”) Mill Speed: 405 m/min. (1330 Fpm) Strip Tension: 2670 kg (5875 Lbs) Coil ID 406 mm (16”) Coil OD 1448 mm (57”) Coil weight: 3180 kg (7000 lbs)

VERRINA CLR 216 X 4050 Sheet metal round bending machine Double roller with 4 rollers and double pressure Year of manufacture 1979 Capacity 4000 mm x 16 mm Roll length 4050 Roll diameter side rolls 370mm top & bottom roll 410mm Roll rise and fall 370mm Input 400/3/50 Hz 52 kW Rolling speed 2.9 / 3.9 / 6.8 meters per minute Control control panel Equipped with hydraulic drop, safety cable hoist Length 9000mm Width 2350 mm Height 2400 mm Net weight approx. approx. 29,500 kg

sheet width: 1000 mm plate thickness: 5,0 mm distance between columns: 1070 mm diameter of upper rolls: 130 mm total power requirement: 4,0 KW weight of the machine ca.: 1,15 t dimensions of the machine ca.: 2,55 x 0,65 x 1,1 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1290 mm plate thickness: 5 mm pre-bending: ja roll diameter: 120 mm roll speed: 1 - 6 m/min total power requirement: 1,1 kW weight of the machine ca.: 825 kg Asymmetry roll arrangement, pre-bending ist possible. This new machine is in the following sizes obtainable: working length from 1040 until 2540 mm, max. plate thickness ( 400 N/mm² ) from 1 until 6,5 mm. We are distributor only for Germany. Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3554 mm plate thickness: 42 mm pre-bending: 36 mm Control: total power requirement: kW weight of the machine ca.: 49 t dimensions of the machine ca.: 7.3x2.4x2.5 m Stocknumber 2210024 Type of machine 4-roll CNC Plate bending machine Make FACCIN Type 4HEL 3554 Build in 2000 Type of control CNC Additional information Cap. 3554 x 42 mm prebending 36 mm Toprolldiam. 540 mm underrolldiam. 530 mm siterolldiam. 430 mm 55 Kw LxWxH= 7350 x 2400 x 2500 mm weight of the machine 49 ton The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3050 mm plate thickness: 53 mm pre-bending: 45 total power requirement: 60 kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210020 Type of machine 4-Roll Plate Bending machine Make DAVI Type MCB 3053 Build in 1998 Type of control Conventional Additional information max. Plate widht 3050 mm Max. plate thickness 53 mm Max. thickness prebending 45 mm Toprol diameter 525 mm under roll diam. 470 mm Site rolls diam. 400 mm Power 78 Hp Hardened rolls Conical bending Dimensions: 6000 x 3100 x 6700 mm in very good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets with ...

CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets with ...

Make: RIJVA Model: 502/1 S/N: 405 Cap: 12 tons

material width: 300 mm material thickness: 2,0 mm : max. 90° Grad weight: 12 Kg dimensions: 400 x 250 x 100 m Combined sheet metal working machine with: - Bending, tool widths 25 - 50 - 75 - 75 - 105 mm. - Rolls, roll diameter 38 mm - scissors, max. 1015 x 1mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Various parts for straightening machines Ungerer, strip width 1500 - 1700 mm - Straightening rollers, stutz rollers, bearing frames, coupling shafts .. - Gears - Engine - Gearboxes, etc. More info on request

Year 2014 - twin orbital grinding/polishing pads. with extraction & filtration

4-roll plate bending machine Mod. VRM NG HY 3000x40 Country of manufacture: Switzerland YOM: 1997 Brand: HAEUSLER AG Roll diameter 560/540/400 mm Roll thickness 40mm Roll length 3000mm Motor motor Power:55kW System: Hydraulic Voltage: 380V/3 phase Weight 45 000kg The quality of the machine is still very good.

Plate shears Cutting capacity 1 mm Cutting width 1.10 m Foot operation, the cross step is missing.