fasti sac levha çalışması kullanılmış satılık

Hand-operated 3-roll sheet metal round bending machine with asymmetrical roller order Specifications: - Working width max. 1020 mm - Material thickness max. 1.5 mm - Roller diameter 64 mm - Upper roller turned into a crown, can be swung forward - Rear shaft with handwheel diagonally adjustable for conical rounding - Lower roller adjustment with control lever and eccentric - Front shaft parallel - Space requirement approx. W 1250 x H 950 x D 750 mm - Weight approx. 200 kg

Motorized Rounding Machine Foot Holder one. Rear angle infeed Emergency stop leash very good condition Colour: grey Total power requirement 16 A Shaft diameter: 65 mm Capacity: 1020x1.5 mm Weight: 300 kg Machine number: 05 125 001 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.

Max bending length: 1020 mm Max. sheet metal rod: 2 mm steel motor upper cheek adjustment via foot switch manual rear stop diverse bending rails

Punching machine, punching device, hole punching machine, multi-head punch, multi-head punch, punching system -Quantity: 5x punches -Max. width: 1000 mm -Tool built-in: 8x45 mm -Distance between punches: 187 mm -powered: electric -Weight: 280 kg

Maximum cutting length: 4000 mm Maximum sheet thickness: 4 mm steel Driven back gauge to 1000 mm Page fence and table extensions Cutting length limit Cutting edge lighting Protection fence, roll with safety switches Weight: 8500 kg

Key data: 2040 , 2

Motorized swivel bending machine Manufacturer Fasti Type 2095-20-2 Sheet power 2040 x 2 mm at 400 N/mm2 Digital display of the bending angle Foot pedal Notaus Power connection 400V

Specifications: - working width 2540 mm - max. cutting capacity St 40 4 mm - mot. Cutting angle adjustment - Cut gap. by scaled adjustment screws - Number of hydraulic holders 14 pcs - Mot. backgauge with positioning. 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per min - Hydraulic drive 400 V / 7.5 kW - Table height 1030 mm - Space requirement approx. W 2500 x H 1630 x D 2150 mm - Weight approx. 3600 kg - with: - Sheet metal holding pneum. supported - front angle stop + support arms - Electronic cutting depth adjustment - Cut line lighting - E-foot switch

sheet thickness: 1.25 mm steel Roller center distance: 63 mm

sheet width: 2035 mm plate thickness: 6 mm distance between columns: 2000 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m motorized limit stop behind foot switch Technische Daten / technical details: Schnittleistung (Blechdicke) / max. cutting capacity (thickness of sheet) 6 mm Schnittlänge / max. cutting length 2035 mm Hinteranschlag / arrester behind 1000 mm Ständerweite / distance between columns 2000 Mm Antriebsleistung / drive capacity 11 kW Gewicht der Maschine / weight 3500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1020 mm, 2 mm

Max. bending length: 1020 mm Max. sheet thickness: 2 mm steel Upper beam can be swung out Bending angle adjustable via potentiometer Lifting height can be pre-selected via scale Manual and automatic bending mode possible Weight: approx. 650 kg

sheet width: 3000 mm plate thickness: 3 mm weight of the machine ca.: t 3 support arms 1 angle stop pneumatic hold-down device Backgauge to be operated by hand The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

with stop plate and 3 sets of rollers Projection:approx. 240 mm Color: Green Roller center distance: 63 mm Pick-up shaft: 25 mm Sheet thickness: 1.25 mm Dimensions:1200 x 800 x 1400 mm Weight: 70 kg Machine number: 7541002 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.

Gr. working width: 1520 mm for sheet metal up to: 1.5 mm Opening width upper beam: 220 mm Adjustability bending beam: 60 mm Weight: approx. 450 kg Space requirement: 2150 x 430 x 1500 mm

Offer 24289 Specifications: - Max. cutting width 3060 mm - Max. cutting capacity at 45 Kp/mm² 4 mm - Cutting angle 1.50 ° - Cutting gap - adjustment via adjustment screws - Number of hold-downs 15 pcs - Stroke rate 23 to 43 rpm - Front angle stop -Mot. Positioning-controlled back gauge 15 - 850 mm - Cut line illumination - E – Footswitch - Drive 400 V / 7.5 kW - Space requirement approx. W 3900 x H 1600 x D 2400 mm - Weight approx. 4.5 t

Key data: 2040 mm, 3 mm

Max. cutting length: 2040 mm Max. sheet thickness: 3 mm steel Manual backgauge up to 500 mm Side stop and table extensions Knife sharpened 2300 kg

Specifications: Max. sheet width: 2500 mm Max. sheet thickness: 8 mm Weight, approx.: 6400 kg

Key data: 1500 mm, 1 mm

Max. bending length: 1500 mm Max. sheet thickness: 1.5 mm steel Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via limit switch Manual backgauge Weight: approx. 1000 kg

sheet width: 2040 mm plate thickness: 3,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 2,30 t dimensions of the machine ca.: m Manual back stop up to 500 mm Side stop and table extensions Knives sharpened The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3000 mm plate thickness: 6,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 6,50 t dimensions of the machine ca.: m Motorized back stop with digital display up to 1000 mm Side stop and table extensions Cutting length limitation Cutting edge lighting Hydraulic shear angle adjustment Knives sharpened The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2040 mm plate thickness: 3,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 2,30 t dimensions of the machine ca.: m Manual back stop up to 500 mm Side stop and table extensions Knives sharpened The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2040 mm, 3 mm

Max. cutting length: 2040 mm Max. sheet thickness: 3 mm steel Manual backgauge up to 500 mm Side stop and table extensions Knife sharpened 2300 kg

Key data: 3000 mm, 6 mm

Max. cutting length: 3,000 mm Max. sheet thickness: 6 mm steel Motorized backgauge with digital display up to 1000 mm Side stop and table extensions Cutting length limitation Cut edge lighting Hydraulic shear angle adjustment Knife sharpened Weight: approx. 6500 kg

Key data: 2040 mm, 1 mm

with rebate groove in the upper shaft, with steel wheel and scale, solid, stable construction, with wire inserts, 70 mm feed of the rear roller, Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2040 mm Sheet thickness: 1.0 mm Colour: green Machine weight: 600 kg Dimensions: 2200 x 650 mm Diameter:. 70 mm Machine number: 8413105

Specifications: Working length: 3240 mm Bending capacity steel: 4.0 mm Bending capacity stainless steel: 3.0 mm Bending capacity aluminum: 8.0 mm CNC control: SIEMENS Simatic HMI Bending angle adjustment: 0 – 150° Upper beam opening: 350 mm Infinitely variable bending speed Programmable Backstop Hydraulic upper tool clamping Motor power: 7.5 kW Dimensions (length x width x height9: approx. 5000 x 2450 x 2200 mm Weight: approx. 7 to

sheet width: 2040 mm plate thickness: 3 mm daylight upper clamping: 350 mm bending angle max.: 0-135 ° adjustment of lower and bend clamping: 80 mm control: Fastimatic M200 power requirement: 2,2/1,5 kW weight of the machine ca.: 2460 kg dimensions of the machine ca.: 3,2 x 2,8 x 2,1 m Condition: ready for operation: Condition: very good: CE signed: Video available on our website.: Electric 400 Volt: CNC-control with screen: Mot. back gauge: 1000 mm Foot switch: Motorized machine with motorized bending beam adjustment for setting the sheet thickness, screen control Fastimatic M200 (DELEM FM 200 B) for controlling the top cheek stroke, the bending angle and the back gauge with max. 30 working steps, emergency stop switch with magnetic holder, back gauge with ball screw spindles, CE mark. The bending performance refers to sheets of strength of 400 N / mm². Little used machine, ver ...

Manufacturer: FASTI Model: 527 - 12 - 4.0 Year of Manufacture: 2002 Maximum Sheet Thickness: 1290 mm x 4.0 mm (at 400 N/mm² tensile strength) Weight: 1900 kg Find more here - / Contact us at -

Key data: 4 mm, 1500 kg

Fasti Beading Machine Size 4 150x 4mm Power max projection 500mm hydr. Feeding of the upper roller by foot switch Right-left rotation Nkebmd R E Ijv Tqy Njgsw Stepless speed adjustment by handwheel Holder 60mm Weight approx. 1500kg with accessories Built in 1963 Space requirement approx. 1000x1000x1750mm

Max. sheet thickness: 2 mm steel Max. blank diameter: 1000 mm Motorized drive via foot switch

Key data: 1270 mm, 2 mm

Max. bending length: 1270 mm Max. sheet thickness: 2.25 mm steel Bending rail ground Manual backgauge 1200 kg

Key data: 1020 mm, 2 mm

Max. bending length: 1020 mm Max. sheet thickness: 2 mm steel Weight: approx. 500 kg

sheet width: 2500 mm plate thickness: 3 mm distance between columns: 2540 mm total power requirement: 9 kW weight of the machine ca.: 5,5 t dimensions of the machine ca.: 3,5 x 3,5 x 2 m No. 5120 Swivel bending machine FASTI 212 Working area: 2500 x 3 Sheet support behind the machine Space requirement approx. 4 x 4 (2) x 2 m Weight approx. 5.7 tons The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 4040 mm, 4 mm

Max. cutting length: 4040 mm Max. sheet thickness: 4 mm steel Motorized adjustable backgauge with digital display up to 1000 mm Pneumatic sheet hold-up Side stop and table extensions Cutting length limitation Cut edge lighting Weight approx. 7500 kg

plate width: 2503 mm plate thickness: 4.0 mm ST plate thickness: 2.5 mm VA plate thickness: 6.0 mm ALU number of strokes - loaded: 15 - 20 Hübe/min cutting angle: 1.7 ° work height max.: 900 mm Control: ELGO TYP 85 total power requirement: 8.5 kW weight of the machine ca.: 3400 kg range L-W-H: 2913 x 2250 x 1760 mm Features: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge with ELGO control unit - Manual cutting gap adjustment - Front support table including recessed grips - 1x sturdy side stop with scale and tilting cam - 2x sturdy front support arms - 1x freely movable foot switch - Front finger guard - Front emergency stop button - Operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t chamfer lenght: 3050 mm distance between columns: 2550 mm ajustment speed: 90.0 mm/sec working feed: 10.0 mm/sec return speed: 75.0 mm/sec stroke: 140 mm dayligth: 375 mm column arm: 250 mm table width: 90.0 mm work height max.: ca. 950 mm Number of working hours: 14.100 h total power requirement: 13.5 kW weight: 8500 kg range L-W-H: 3630 x 2300 x 2505 mm From a maintenance workshop Good / well-maintained condition With only approx. 14.100 operating hours () Equipment: - CNC electro-hydraulic press brake - DELEM CNC control - model DA 58 Swiveling control panel, front left 2D graphic programming & product display Tool & program library - CNC-controlled axes: Y1+Y2 / X1+X2 / R1+R2 / Z1+Z2 / CNC crowning - CNC electro-motorized backgauge (X axes) Stop system with 2x CNC-controlled gantries - CNC electro-motorized height adjustment of the backgauge (R axes) - CNC ele ...

sheet width - max.: 2535 mm plate thickness: 4.0 mm ST plate thickness: 2.5 mm VA plate thickness: 6.0 mm ALU number of strokes - loaded: 20 Hub/min cutting angle: 1.7 ° work height max.: 900 mm total power requirement: 8.5 kW weight of the machine ca.: 3400 kg range L-W-H: 2916 x 2250 x 1760 mm Machine from training workshop good / well-maintained condition () Equipment: - robust electro-hydraulic swing cut guillotine shears - electro-motorized rear stop - electric cutting length limiter - electro-motorized cutting gap adjustment - front support table including recessed grips - 1x stable side stop, with scale and tilting cam - 3x stable, front support arms - 1x freely movable foot switch - front finger guard - EMERGENCY STOP button at the front - operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts The data for this ad was ...

sheet width - max.: 1255 mm plate thickness: 4.0 mm ST plate thickness: 2.0 mm VA plate thickness: 6.0 mm ALU number of strokes - loaded: ~ 66 Hübe/min. cutting angle: 1.5 ° total power requirement: 5.5 kW weight of the machine ca.: 2600 kg. range L-W-H: 2300 x 1800 x 1800 mm Machine from a technical college - prototype construction very well-maintained condition () Furnishing: - electro-hydraulic guillotine shears - manual backgauge with analogue position display (scale + magnifying glass) - electrical cutting length limitation - manual cutting gap adjustment - 1x extra long side stop - 2x extra long support arms - 1x free moving footswitch - rear sheet metal slide - User manual (PDF) Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9325278 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1270 mm plate thickness: 1.75 mm ST plate thickness: 2.00 mm ALU plate thickness: 2.50 mm KU thickness at Niro-steel: 0.80 mm distance between columns: 1300 mm daylight opening: OW ~ 380 mm work height max.: 900 mm adjustment: UW 60.0 mm bending angle max.: 180 ° weight: ca. 200 kg kg range L-W-H: 2000 x 520 x 1500 mm good condition () Bending splint e.g. reground Furnishing: - robust, manual folding machine - manual lifting by hand lever (incl. gas pressure damper) - manual clamping of the upper beam by means of a handwheel on the side - manual lower beam adjustment - Bending angle fixed stop, with analogue angle display - Upper beam with large opening width - Instructions / description Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9355182 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3240 mm, 5 mm

Max. bending length: 3240 mm Max. sheet thickness: 5 mm steel Upper beam stroke: 350 mm Program control via touchscreen (back gauge, bending angle adjustment, stroke of the upper beam, sheet thickness, number of pieces, etc.) Motorized height adjustment of the bending beam (adjustment of the sheet thickness) Manual and automatic mode possible Controlled backgauge with spring fingers Central lubrication Various additional bending and reinforcing rails Operating instructions 5700 kg

gt; cap: 5 ton gt; max width: 1100 mm gt; manual clamping gt; non-driven unit

Hoort bij Lijn -gt; P.14d 15917

Max. bending length: 1270 mm Max. sheet thickness: 1.75 mm steel Motorized upper bolster adjustment via foot switch Automatic backgauge

sheet width - max.: 1010 mm plate thickness: 4.0 mm ST plate thickness: 2.5 mm VA plate thickness: 6.0 mm ALU number of strokes - loaded: max. 20 Hübe/min cutting angle: 1.5 ° work height max.: 900 mm Control: ELGO total power requirement: 5.5 kW weight of the machine ca.: 2200 kg. from a maintenance workshop good condition () Equipment: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge Includes NC ELGO positioning control TYP 85 - Electric cutting length limiter - Manual cutting gap adjustment - 1x side stop with scale - 2x support arms - 1x freely movable foot switch - Original operating instructions Special accessories included: - Pneumatic holding device for thin sheet metal blanks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4040 mm plate thickness: 4,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 7,50 t dimensions of the machine ca.: m Motorized adjustable backgauge with digital display up to 1000 mm Pneumatic sheet metal support Side fence and table extensions Cut length limiter Cut edge lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. bending length: 2540 mm Max. sheet thickness: 3 mm steel Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via dip switch Bending rail ground Weight: 3400 kg

sheet width: 2040 mm plate thickness: 4,00 mm distance between columns: mm upper beam stroke: 350 mm total power requirement: kW weight of the machine ca.: ca.4,00 t dimensions of the machine ca.: m Manual and automatic bending sequence possible Bending angle adjustable via potentiometer Upper jaw stroke height and material thickness selectable via DIP switches Bending rail in excellent condition Manual backgauge with spring fingers The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1520 mm, 3 mm

Asymmetrical 3-roll round bending machine with 2 motors Lower roller crowned 110 mm diameter Upper roller (swing-out) crowned 90 mm diameter Rear roller (motorized adjustable with digital display) crowned 110 mm diameter Double footswitch Weight approx. 1200 kg

A cassette set of bending tools for FASTI MAK

Key data: 2540 mm, 8 mm

Max. bending length: 2540 mm Max. sheet thickness: 8 mm steel Upper roller diameter: 200 mm Clockwise and counterclockwise rotation via footswitch Safety rope hoist Conical rounds possible Motorized rear roll infeed Lower roll feed via handwheel with position indicator Weight: approx. 4,500 kg

A high-performance crank plate shear with a low operating hours count is offered. Design: all-steel welded construction, stroke rate: 50 strokes/min, control FM 1S, backgauge manual or motorized (MAH 51/52), pneumatic hold-down device, rear safety light barrier. Inspection possible by arrangement.

Max. bending length: 2040 mm Max. sheet thickness: 3 mm steel Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via dip switch Manual backgauge with spring fingers Weight: approx. 2300 kg

A two-roll plate rolling machine Fasti is available. Roll diameter: 130mm, working width: 2150mm, max. sheet thickness: 3.5mm. Machine dimensions X/Y/Z: approx. 2900mm/650mm/1100mm, weight: approx. 1200kg. Documentation available. An on-site inspection is possible.

Max. bending length: 2040 mm Max. sheet thickness: 4 mm steel Max. upper bolster stroke: 350 mm Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via toggle switch Bending rail in top condition Manual backgauge with spring fingers 4000 kg

sheet width: 3040 mm plate thickness: 4 mm distance between columns: 3040 mm stroke of upper beam: 200 mm adjustment of lower and bend clamping: 100 mm total power requirement: 6,4/3 kW weight of the machine ca.: 6,3 t dimensions of the machine ca.: 4,3 x 1,2 x 1,8 m Condition: ready for operation: Electric 380 Volt: Control panel: Winkelvorwahl Holder for divided upper tools: Upper tool divided: 3040 x 120 mm Hnad control: Sheet metal shelf behind: Folding blade: Flat rail for folding beam: Motorized folding machine with double-sided bending beam drive, lower, upper and bending beam adjustable, drive motors as brake motors - slip clutches as overload protection, bending angle adjustment via potentiometer, individual switching for each work step by hand switch, SEGMENTED TOP RAIL 120 mm height (Photo 7).Please notice that such a machine now costs about €70.000,--. As usual, the  ...

Fasti 2040 x 5 mm Number of rolls: 3 rolls Roll capacity cold: 2040 x 5 mm Roll dia upside: 160 mm Power needed: 7,5 HP Length: 3250 mm Depth: 900 mm Hight: 1300 mm Weight: 3100 kg

Type: 108 Number of rolls: 3 rolls Roll capacity cold: 2540 x 2,5 mm Roll dia upside: 140 mm Dia under roll - side rolls: 140 mm Power needed: 5 kW Weight: 1760 kg

Type: 230 Maximale buighoek: 180° Max worklength: 2040 mm Max tickness: 1,5 mm Distance between clampblock -- ram: 100 mm Eletric motor (power): 0,75 kW Weight: 1000 kg

De plaatdikte is afhankelijk van het profiel. dop: 0,5 gt; 1,5 mm 7 stations vermogen: 2,4 kW gewicht: 430 kg

serial number: 70212008 weight: 3,3 t working width: 2040 mm : 4 length: 2900 mm width: 1890 mm height: 1780 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. bending length: 2540 mm Max. sheet thickness: 5 mm steel Upper beam stroke: 350 mm Manual and automatic mode possible Motorized adjustable back gauge with spring fingers and digital display Central lubrication Segmented upper and lower beam rail for 2050 mm 5600 kg

sheet width: 2040 mm plate thickness: 3,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 2,30 t dimensions of the machine ca.: m Manual and automatic bending operation possible Bending angle adjustable via potentiometer Upper jaw stroke height and material thickness selectable via DIP switches Manual backgauge with spring fingers The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2040 mm plate thickness: 4,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 3,00 t dimensions of the machine ca.: m Controlled backgauge up to 1000 mm Side fence and table extensions Cut length limiter Cut edge lighting Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3240 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 3,00 t dimensions of the machine ca.: m Manual and automatic bending operation possible Bending angle adjustable via potentiometer Upper beam stroke height and material thickness selectable via DIP switches Bending rail and machine in excellent condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. bending length: 3240 mm Max. sheet thickness: 2 mm steel Manual and automatic bending process possible Bending angle adjustable via potentiometer Lifting height of the upper beam and material thickness can be preselected via dip switch Bending rail and machine in top condition Weight: approx. 3000 kg

Max. cutting length: 1040 mm Max. sheet thickness: 4 mm steel Manual backgauge up to 550 mm Side stop and table extensions Knife sharpened 1700 kg

Key data: 50 t, 2550 mm

Hydraulic press brake Manufacturer Fasti Type UBGP 50/25 max pressing pressure 50t max working width 2550mm Lifting height 150mm with block matrix and div segments Press is in a used 100% functional condition. Can be loaded with overhead crane.

FASTI Type 63x1.5 Beading Machine -Condition / Mint -Upper beading roller hydraulically adjustable -Control panel -Various beading tools -Hydraulic power unit Dimensions: Cjbkn Aswxfz Doug Nogw LxWxH 1.6x0.8x1.7 meters / Weight 1200Kg

Max. bending length: 1020 mm Max. sheet thickness: 1.5 mm steel Weight: approx. 300 kg

Fasti - Round bending machine / type 2040x2mm -GS / Identifier -Roller diameter 105mm -Max. sheet thickness over the entire length 2mm -Footswitch -Safety device Dimensions: LxWxH 3x1x1.3 meters / Weight 1400Kg Hebjvdnahskn Au S Tsl

Key data: 2540 mm, 6 mm

Max. cutting length: 2540 mm Max. sheet thickness: 6 mm steel Motorized adjustable back gauge (2 speeds) up to 1000 mm with display Side stop and table extensions Cutting length limitation Cut edge lighting Weight approx. 5500 kg

sheet width - max.: 3035 mm plate thickness: 4.0 mm ST plate thickness: 2.5 mm VA plate thickness: 6.0 mm ALU number of strokes - loaded: 20 Hübe/min cutting angle: 1.7 ° work height max.: 900 mm Control: ELGO total power requirement: 8.5 kW weight of the machine ca.: 4400 kg range L-W-H: 3416 x 2250 x 1760 mm Equipment: - robust NC electro-hydraulic guillotine shears - NC electro-motorized backgauge with ELGO control unit TYPE 85 - Manual cutting gap adjustment - front support table incl. recessed grips - 1x stable side stop, with scale and tilting cam - 3x stable front support arms - 1x freely movable foot switch - front finger guard - Rear metal slide - EMERGENCY OFF button at the front - Operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. sheet thickness: 3 mm steel Roller center distance: 125 mm Largest radius: 500 mm Clockwise and counterclockwise rotation Weight: approx. 500 kg Other castor sets on request

Three-roll bending machine, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll bending machine, profile bending machine, three-roll sheet metal rolling machine, manual bending machine -Roll bending machine: 3-roll roll bending machine, electrically driven -Bending adjustment: electric -Max. sheet width: 2040 mm -Max. sheet thickness: 4 mm -Roller diameter: 150 mm -Dimensions: 1080/2880/H1370 mm -Weight: 1770 kg

Punching machine, punching device, hole punching machine, multi-head punch, multi-head punch, punching system -Division: 8 x punch pairs with a spacing of 60 mm (Ø 4 mm) -Distance between the two outer pairs of punches: 975 mm -Spacing: 75 - 165 - 165 - 165 - 165 - 165 - 165 - 75 mm -Max. passage width: 1000 mm -Drive: electric -Weight: 260 kg

electric clutch, electromagnetic clutch for guillotine shear, sheet metal shear, sheet metal guillotine shear, crank guillotine shear, eccentric press -for: Crank-operated guillotine shears -Equipment: Coupling, transformer, control unit -Manufacturer: LABOD electronic -Type: GN 6 DZ.4Q.80 -Total net weight: 160 kg

Max. cutting length: 2040 mm Max. sheet thickness: 2 mm steel Manual backgauge up to 500 mm Side stop and table extensions Knife sharpened 1900 kg

Manufacturer: Fasti Model: 902-315/40 Year of Manufacture: 1990.The machine was last retrofitted in 2019. Type of Machine : Bending Machine Technical Specifications - Total Weight : 25,000 kg - Nominal Pressing Force : 3150 kN - Stroke Length: 250 mm - Working Width: 4050 mm - Maximum Working Pressure: 30 MPa - Stopping Time: 71 ms - Two-Hand Release Safety Distance : 114 mm Find more here - / Contact us at -

Key data: 1020 mm, 3 mm

Max. bending length: 1020 mm Max. sheet thickness: 3.5 mm steel Bending rail ground Weight: approx. 1000 kg

Offer 26017 Technical data: - Max. projection 250 mm - Working depth 217 mm - Roller center distance 80 mm - Max. material thickness at 40 kg/mm² strength 1.75 mm - Working speed infinitely adjustable - Right + Left Rotation - Drive 400 V 1.1 / 1.4 kW - Space requirement approx. W 500 x H 1450 x D 655 mm - Weight approx. 250 kg - with: - E - foot switch - Roller sets - Anchor apron

Gr. working width: 4040 mm for sheet metal with a strength of 40 kg up to: 3 mm Upper bolster adjustment: 400 mm Underbeam adjustment approx.: 80 mm Max. bending angle adjustment electrically up to approx.: 180° Upper bolster variable speed drive: 4 kW Bending beam drive: 2 x 3 kW Back gauge, working range: 10 - 750 mm electr. Connection: 400 V Weight: 9 t Space requirement: 5570 x 2250 x 2000 mm high

Key data: 1250 mm, 4 mm

Max. cutting length: 1250 mm Max. sheet thickness: 4 mm steel Controlled backgauge Side stop and table extensions Cutting length limitation Cut edge lighting Light barrier to protect the rear area Knife sharpened Weight approx. 2800 kg

Offer 26084 Technical data: - Max. working width 2040 mm - max. material thickness at 40 kg / mm² strength 4 mm - Bending angle adjustment electronically pre-selectable 0 - 135 ° - Automatic follow-up control for a complete workflow - Largest opening width / stroke of the upper beam 350 mm - Height adjustability - bending beam 100 mm - The lower beam 100 mm - Upper bolster drive 400 V / 4 kW - Bending beam drive 400 V / 4 kW - Bending beam adjustment - Backgauge adjustable with handwheel - E-foot button - Space requirement with back gauge - approx. W 3200 x H 1650 x D 2100 mm - Weight approx. 4500 kg

sheet width: 2040 mm plate thickness: 4,0 mm distance between columns: 2100 mm roll diameter: 150 mm total power requirement: 7,0 KW weight of the machine ca.: 2,2 t dimensions of the machine ca.: 2,95 x 1,0 x 1,75 mm Sheet metal bending machine with 3 rollers - 2 driven rollers - Rear roller electrically adjustable - Conical bending - Foot switch - Emergency stop device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width:5040 mm plate thickness:2 mm total power requirement:12 kW weight of the machine ca.:9,4 t dimensions of the machine ca.:6200× 1300 ×1900 mm working width:5000 mm control:Fasti Matik stroke of upper beam:500 mm adjustment of lower beam:u.Biegewange 80 mm control cabinet:1000 x 850 x1450 mm Documents:vorhanden

guillotine shears AG TS 2 Working thickness 2mm Adjustable stop Hold Length 1.80 m Width 1 m Height 1.40 m Weight 300 kg

Line Salvagnini S4 P4 Year 2001/2003 S4 30 + P4 2220 + MD with unloading robot. Working line, regular assistance performed by the manufacturer