hess taşlama makineleri ahşap çalışma kullanılmış satılık

Key data: 190 mm, 2

Grinding Machine HESS Double-Sided Grinding Machine Type: GLORIA Year of Make: 1995 CE Grinding width 190 mm Grinding thickness 4 – 180 mm Sanding shoe and brush from above Sanding shoe and brush from below Oxyd ceramics are wear-free and therefore maintenance-free Motorized height adjustment with digital display Shortest workpiece length 300 mm oscillating abrasive belts Sanding belt blow-off nozzle Workpiece transport via conveyor belts Sanding belt width 200 mm x sanding belt length 1600 mm Grinding motor 2 x 4 kW Feed speed infinitely variable 5-25 m/min. Feed motor 0.75 kW Height adjustment 0.18 kW Sanding belt speed 24 m/sec. Working height – table height 830 mm Suction connection nozzle diameter 2 x 160 mm Extraction air volume 2x2000-2500 m³/h Machine dimensions: Length 1660 mm x width 1030 mm x height 1820 mm Height with suction nozzle 1930 mm  ...

Cylinder go Hess frame press with pneumatic 3 vertical and 2 horizontal cylinder

Frame press Hess economic hydraulic 3600 x 2250 mm L x W x H: 400 x 100 x 270 cm Weight approx. 1100 kg year 1987 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Frame press Hess hydraulic Type: HYDRO-LUX Crimping dimension approx. L 3550 m x W 2250 mm Connected load 380 V / 50 Hz 2.6kw Hydraulic Pump Machine dimensions Length 6600 mm x Width 1600 mm x Height 2770 mm 0 - 8 bar pneumatic Optoelectronic measurement query. The window scantlings are placed in the feed channel so that the photoelectric sensor can measure whether the pressure beams and press corners need to be opened or closed. If the light beam of the probe hits the window scantlings, the machine receives the command to drive up in width and height until the working dimension is reached. Workflow: Automatic dimensional adjustment loose insertion Automatic pressing process loose presentation remove Automatic dimensional adjustment Program selection options in the control system: 1. Automatic measurement adjustment via optoelectronic measurement query with a ...

Cup hinge drilling machine -Stops: pneumatically controlled with program selection -Drilling pattern: see the pictures -Dimensions: 4000/1100/H1800 mm

Frame press Hess Technical description: - 2 pneumatic pressure cylinders in length - 2 pneumatic pressure cylinders in width - 2 pneumatic workpiece holders - Feed bandwidth: approx. 680 mm - Feed belt length: approx. 3,400 mm - Clamping area: 680 x 1,400 mm - Control panel Dimensions: - Length: approx. 3,400 mm - Width: approx. 1,700 mm - Height: approx. 1,400 mm - Weight: approx. 800 kg

Edge Press Hess Type mobil 3000 Machine No. M 2 2791 1538 Year of manufacture 1991 Working length 3000 mm Pneumatic Banding width 60 mm Pressure range 0 – 8 bar 6 press cylinders, pressure plate 120 mm diameter Mobile on castors Heavy version Heating element 0 – 200 °C Solid edge preheating device Length 3200 mm x width 850 mm Weight approx. 450 kg

Gluing star with heating plates. Connection 30 KW. Four pressing surfaces. Hydraulic, pneumatic. Further dates will follow.

Number of boring motors: 1 St. boring of corner bearing 1=yes, 0=no: 1 ja_yes boring of olive 1=yes, 0=no: 1 ja_yes 1 HESS fitting drilling station for corner bearings and olives This Hess drilling station for tradesmen offers a lot of drilling technology for little money. A complete station for drilling corner bearings and olives with all the important features, such as 2 clamping cylinders, drilling depth sensing, effective suction, stop systems for corner bearing and olive drilling, drilling head with interchangeable chuck, adjustable drilling feed speed, automatic program sequence. This means technology for perfect work: just one machine with just one drilling unit and just one drilling head for 2 work steps. The system: - Base frame as a support wall for frames and sashes up to 100 mm - Drilling unit positioned in the middle, height manually adjustable via threaded spindle - Drill h ...

Number of sanding units: 2 st. sanding width: 190 mm Sanding height max.: 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----------------------------------------------------- Machine is being checked! Manufacturers description: ----------------------------------------------------- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the dust-tested certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the ...

Number of sanding units: 4 St sanding width: 190 mm Sanding height max.: 4-180 mm weight: 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians -------------------------------------- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geom ...

Frame press Hess Type VARIANT Machine No. 2182 Built in 1979 Pneumatic Frame Press Workspace 3700 mm x Height 2300 mm 4 bars with pressure cylinders from above Stop side left 1 movable pressure bar from the right with 2 pressure cylinders Cylinder stroke 110 mm Compressive force per cylinder 1100 kp (1kp = 1kg) Compressed air connection max. 15 bar Weight approx. 550 kg Exterior Dimensions 4400 mm x 700 mm x H 2800 mm Loading dimensions 4400 mm x 600 mm x H 2300 mm + Pallet with pressure beam 2800 mm x 800 mm x H approx. 700 mm

Manufacturer: Hess , Type: Centro, Year: 2000, Hydraulical/pneumatical: yes, High / low pressure: yes, Press length mm: 3050, Press height in mm: 2200, Press depth mm: 100, Cylinder vertical: 2, Cylinder horizontally: 2, Vertikaldruckzylinder: 2, Haltezylinder zum Fixieren der Hölzer: yes, Mitteldruckbalken: no, Querdruckeinrichtung: yes, Funk-Handpanel: Handpanell, Elektronische Einzeldruckregelung (zum Verpressen von Kreuzsprossenfenster): yes, Year :2000

Manufacturer: Hess , Type: Rahmenpresse, Year: ca.1995, Work piece width min-max mm: ca.1500, Min.-max. workpiece length in mm: 2500, Min.-max. workpiece height in mm: 10-90, Working widht max mm: 2500, Hydraulical/pneumatical: elektrisch, Year :ca.1995

Manufacturer: Hess, Type: Kantenpresse, Working length mm: 2500, Working widht mm: 2000, Carriage: yes, Pneumatik: yes, Cylinder: 80, Wight approx. kg: 300,

Manufacturer: Hess, Type: Mobil Kantenbügelpresse, Min.-max. workpiece height in mm: 60, Pre-warming of massive edges and heating rod: yes, Working length mm: 1.100, Working widht mm: 1.100, Carriage: yes, Tiltable design: yes, Cylinder: 2,

Manufacturer: Hess, Bauyeshr : 1997, Hydraulical/pneumatical: hydraulisch, Press length mm: 3800, Press hight mm: 2900, Machine rigging: hand, Wight approx. kg: 4000, Year :1997

Manufacturer: Hess, Type: Junior, Year: ca1987, Control: L/L, Software: yes, Barcode: 190, Monting of the machine: 4 - 150, Equipment of machine 2: 2, Double sided sanding line: 5 - 25, Steel roller: yes, Steel roller: yes, Belt 1 shoe unit: 5,5, Belt 1 combined unit: 5,5, Band 2 Kombiaggregat Walze/Schuh: 1, Band 2 Innenliegendes Drucklamellenband : yes, Band 2 Schleifbandgeschwindigkeit m/s : 280, Belt 2 pressure segment belt: yes, Belt 2 synchronous and reverse run: yes, Band 3 Kombiaggregat Walze/Schuh: yes, Year :ca1987

Manufacturer: Hess, Type: Speedy Quick Step, Year: 1995, Min.-max. workpiece length in mm: 3500, Min.-max. workpiece height in mm: 2500, Working widht max mm: 600, Hydraulical/pneumatical: hydraulisch, High / low pressure: Hochdruck, Cylinder vertical: 3, Cylinder horizontally: 2, FREE TEXT: Automatisches Verfahren der Balken und Lanhhubzylinder für vertikale Bewegung, Year :1995

Manufacturer: Hess, Type: Kantenbügelpresse, Year: ca.1990, Pre-warming of massive edges and heating rod: 2, Working length mm: 4000, Working widht mm: 60, Carriage: yes, Tiltable design: yes, Pneumatik: yes, Cylinder: 8, Wight approx. kg: 300, Year :ca.1990

Number of sanding units: 2 st. sanding width: 190 mm Sanding height max.: 4-150 mm Hess Junior single wood sanding machine -------------------------------- Machine in checking process at the moment! Basic structure: Stable, heavy welded construction made of thick-walled rectangular hollow profiles with additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and airborne dust extraction with integrated blow-off device. grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. All guides as a ball linear set on hardened and polished waves. Permanent precision thanks to dust and dirt protection the ball linear sets. Contact roller and sanding pad in a balanced ratio for sanding belt grain load. The la ...

Working width: 3500 mm Working height: 2550 mm Number of cylinders: 6 St. loading dimensions L x W x H: 4500x950x2900 mm Hess Speedy frame press -------------------------------------- will be checked Insertion dimension / pressing length max. 3,500 mm Insertion dimension / pressing height max. 2,550 mm Sliding carriage for width adjustment locking in 50 mm Double hole grid system Electric height adjustment of the long-stroke cylinders (hydraulic) Insertion height of the abutment plates can be preselected in 4 positions 3 vertical printing cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 3 horizontal printing cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Printing plate depth 100 mm width 140 mm Grid for cylinder fixation/rear bearing 50 mm Medium pressure beam with shut-off valve Final pressure switch-off and pressure control Control and press ...

Working width: 3450 mm Working height: 2000 mm Number of cylinders: 5 St. loading dimensions L x W x H: 3600 x 1200 x 2720 mm Hess Multipress Perforated Plate Press For all sloped, segmental, and round-arch windows and doors. Also for interior work or frame construction. For gluing staircase block joints and much more. Largest working area approx. 3450 x 2000 mm External dimensions approx. 3600 x 1200 x 2720 mm The vertical perforated plate press is constructed of heavy-duty, torsion-free steel. Thanks to its simple, robust, and economical design, it has a long service life. The perforated plate is made of 10 mm sheet steel with a 50 mm hole pattern. The pressure cylinders and abutments are self-locking. 5 plug-in hand hydraulic cylinders on a perforated plate with a built-in pump, 2000 kp pressure relief valve, 140 mm pressure plate width, 80 mm pressure plate depth, 60 mm cylinder stro ...

Key data: 3550 mm, 2250 mm

Frame press Hess Type SPEEDY Built in 1995 Crimping dimension 3550 mm x 2250 mm Insertion depth 100 mm Electric height adjustment of the press cylinders Hydraulic 160 bar pressure capacity Hydraulic power unit 2.2 kW 3 vertical cylinders: 1000 mm stroke, 20,000 N pressing force per cylinder 2 horizontal cylinders: 80 mm stroke, 12,500 N pressing force per cylinder Smallest dimensions without medium pressure beam horizontal 380 mm, vertical 320 mm Dimensions 4500 mm x 950 mm x H 2600 mm Weight 1,800 kg Loading dimensions Length 4500 mm x Height 2450 mm Width approx. 2400 mm

Code: 0253 Brand: LARI E LARI - ITALY Model: FR 20 - TA - CE Standard Working center for milling and boring on wood or plastic and composite materials, wooden doors, window frames - CE Standard Technical data: X-axis working stroke 3250 mm Y-axis working stroke with 90° cutter 130 mm Z-axis working stroke with 0° cutter 290 mm Z-axis working stroke with 90° cutter 175 mm X-axis working speed mt/min 40 Y-axis working speed mt/min 30 Z-axis working speed mt/min 30 Hinge boring inserting unit: Male/Female Speed control inverter Probe Tool holder collet ER 25 Power of anuba head drilling electric spindle 2,2 Kw Anuba head inclination -10 +90° Electric spindle for milling: 2,7 Hp at 18,000 rpm Collet chuck ER 32 Variable speed via inverter Inclination from 0 to 90° for both vertical and horizontal machining Machine computer: numerical control - Win ...

• Height: 850 - 1000 mm • max length: 2400 mm (extendable) • max. static support load: 225 kg • Dimensions (LxWxH): 1600 x 600 x 850 mm • Weight: 30 kg • Electrical connection: 230 V / 50 Hz • for crosscut saws, belt grinders, cutting saws, etc. • Installation and adjustment without tools • foldable feet for space-saving storage or transport • Quick clamping ssystems enable quick conversion, e.g. for cutting down long workpieces The list price for this work table is € 139.00 (plus VAT). (Changes and errors to technical data and prices reserved!)

SECOND-HAND COPYING ROUTING CARROUSEL WITH 6 WORKING STATIONS CAMAM MOD. GC6/3F/1L - double locking cylinder on each working station - 1 inside/outside milling unit - 1 inside milling unit - 1 outside sanding unit - 4 sides cabin with roof - kw 28 - year 2002

SECOND-HAND COPYING ROUTING CARROUSEL WITH 6 WORKING STATIONS CAMAM MOD. GC6/4F/1L - double locking cylinder on each working station - 1 inside/outside milling unit - 1 inside milling unit - 1 ouside milling unti - 1 outside sanding unit - 4 sides cabin with roof - kw 28 - year 1995

CATALOG NO. 6875 TECHNICAL DATA - inlet width 720mm - inlet height 160mm - thickness of the shredded material 160mm - roller width 720mm - shaft diameter 600mm - knife length 80mm - number of knives 4×12pcs - 25mm sieve dimensions - pressing roller at the input 0.75 kW - toothed shaft pulling from the bottom 1.8 kW - toothed shaft pulling from above 1.8 kW - length of the vibrochute 4470mm - width of vibrochute 710mm - 2.2 kW vibrating motor - main engine 55kW - autoreverse - diameter of the extraction spigot 260mm - dimensions of the vibro-chute length/width/height 4470/950/930mm - machine dimensions length/width/height 3100/1500/1170mm - total weight about 5500 kg – German production - very low mileage – original documentation – used chipper, very good / perfect condition Net price: PLN 169900 Net price: 36538EUR Net price calculated according t ...

Chipper / Shredder WEISS CR40/324MM CATALOG NO. 6907 TECHNICAL DATA - inlet of the loading hopper at the top 1980x1050mm - inlet of the loading hopper at the bottom 980x1050mm - outlet for chipped wood fi 210mm - working width of the rotor 980mm - main engine 30kW - pump motor 1.1 kW - number of knives 36 pcs - knife size 40x40mm - 18mm sieve - pressure drawer - electric autoreverse - dimensions length/width/height 2100x2030x2070mm - weight about 3500 kg - French production – like WEIMA WL 10 - New knives installed – autoreverse – pressure drawer - very good condition – used chipper Net price: PLN 108900 Net price: 23419EUR Net price calculated according to the exchange rate of 4.65 PLN/EUR (with larger exchange rate fluctuations, the price may change)

CATALOG NO. 6926 TECHNICAL SPECIFICATIONS - loading hopper inlet 1200x1000mm - outlet for shredded wood + viper fi 200mm - rotor working width 980mm - main motor 30kW - pump motor 0,75kW - viper motor 0,55kW - number of knives 24pcs - knife size 30x30mm - sieve 10mm, 12mm - pressure drawer - electric autorewers - dimensions length / width / height 2470x2130x1720mm - weight about 3000kg ADVANTAGES C0fhenux8o – German production – autorewers – pressure drawer – viper – very good condition – used chipper Net price: 122900 PLN Net price: 27311EUR Net price calculated according to the exchange rate of 4,5 PLN/EUR (with larger fluctuations in the exchange rate, the price may change)

CATALOGUE NO. 6943 TECHNICAL SPECIFICATIONS - loading hopper inlet 1600x1500mm - rotor working width 1500mm - main engine 45kW - pump motor 5,5kW - number of knives 44pcs - knife size 50x50mm - sieve 59mm - pressure drawer - autorewers - dimensions length / width / height 3430x2800x2850mm - weight about 9000kg ADVANTAGES – French production - new knives put on – autorewers – pressure drawer – very good condition – used chipper Net price: 189900 PLN Net price: 42200 EUR Net price calculated according to the exchange rate of 4,5 PLN/EUR (with larger fluctuations in the exchange rate, the price may change)

Hackeranlage Rudnick Enners 650/200 Motor 37kw vibrorinen Metaldetector kratzforder Containerbefillen

20-75- CNC with tool changer WOODLAND MACHINERY (new) Type SX1325A-12 Useful working area axis X-Y-Z 2850-2100-150 mm Shaft, air cooled, 9.0kw 24000 rpm. Servo motor Control system LNC Drive gear High precision automatic positioning cylinder Work table vacuum plate Vacuum pump 7.5 kw Maximum speed 60 m/min Maximum working speed 15-20m/min Flexible towing cable (with screen) Air components BLCH Voltage 380V/50HZ Transport dimensions 3200x2100x1800mm Weight 3100 kg The price is 24500 Eur

Wood Chipper, Wood shredder 18 KW Opening 600 x 800mm

Horizontal chipper Horacle / machine no.: H2156/62HO - Feed width: 620mm - Max. feed height: 140mm - Vibrating trough length: 5m - Power: 28 kW - Rated voltage: 400V - Rated current: 55A - Control voltage: 230V - Fuse : 63A - Frequency: 50Hz

Type Record 121 Number of working axes 3+ Useful working area axis X-Y-Z 2600-1080-250 mm Table dimensions 2600 x 1080mm Spindle speed 900 - 18000 rpm Number of milling spindles: 1 Tool change positions: 12 Tool clamping system HSK63F Work table Matrix table The main engine is 7.5 kw Vacuum pump performance 250/300 m3/h Vacuum motor 6.5 kw The diameter of the extraction socket is 150 mm Air pressure 7 bar Voltage 380V/50HZ Transport dimensions 3700x3200x2600mm Weight 3500 kg The price is 15500 Eur

900 mm sanding machine for turned products. GENINI mod. LAR90 - Maximum working length 900 mm. - Automatic loader

DMC 3-belt calibrating sander mod. USK1350 M3 - CE standard - 1 steel roller - 2 rubber rollers - 3 rubber rollers - N. 3 independent motors - Working width 1350mm - With shoes (short pieces device) - Blower on the third group - On/off device on each group - Touch screen control - Matr. SA/005006 - Year 2004 - CE compliant

COMEVA horizontal belt sander mod. LC180

CAMAM longitudinal sander mod. LOL/75/RU

CNT orbital sander mod. LOR 150 - CE compliant - Matr. 17002 -Diam. Min. max. machinable 10-45 mm.ù - Hp3 engine - Year 2017

CAMAM orbital sander mod. LEC250 – CE compliant - With feeds - Matr. 11 - Year 1996 - Working dimensions min/max. 30/150 mm. - Min. radius of curvature mm. 250

Hundegger K2i 625 well-maintained year of manufacture end of 2008 fully automatic carpentry machine, feed and loading cross conveyor, under-table swivel cross-cut saw 11 kw, universal milling unit - 5 axis, combined support for vertically working tools, drilling rig 2.2 kw, drilling rig swivel 2.2 kw, marking device, fully automatic beam turning station hydraulic design, transport and position setup two-hand system, electronic control, 6-arm storage table, AQF strand with shaft extension, Extension bracket with puller, zero stop for pre-elongated components, scrap wood holder on the K2 i in front of the sawing unit, splinter wood for horizontal drilling unit, vertical finger cutter 5.5 kw, longitudinal and transverse groove cutter, slitting device on both sides guide 900mm, marking device at the rear, marking and labeling device at the bottom, refined wood support surfaces, additional sc ...

Orbital sander CAMAM mod. LEC200/AV - With feeding units - Min/max diam. 10/100mm - Motor 5.5hp - Volt. 380v/50hz

ZENO Zerkleinerungsmaschinenbau Norken GmbH ZTLL 1000x1200 Waste shredder in use until 03/2026 in good used condition Masch. No. 98A-4689 Standard version, screen hole 20mm Low-speed with moving floor Main drive 18.5 kW, hydraulics 0.75 kW 400/690 V, total rated current 36A Fuse 63A Conductor cross-section 4x16 square Weight 1950 kg, 20 cutting edges Rotor speed 140 rpm Rotor diameter 300 mm Extraction diameter 250 mm Exhaust air speed 30 m/s Inlet cross-section L 1000mm W 800mm External magnetic separator Spare blade

PIN cutting machine Clamping width of 240 mm beam height of 320 mm spigot strengths of Max 130 mm PIN length of 350 mm motor power 2,2 kW 380 Volt motor weight approx. 120 kg

Important and outstanding design features of the RaptorX-SL with steel substructure / RaptorX-SL2200/S20 The application variety of a RaptorX-SL CNC Fraes machine is variable due to the adjustable working area (read-through shoe under bridge: 150mm, 300mm or 400mm ) and the travel height of 300mm in the Z-axis (at no extra charge) extremely large. special groesmes up to 17,500 mm (at one scale ) x 3000 mm x 600 mm are possible ! If you are interested, please ask ! So you are able to process plate materials with the greatest stability of the Z-axis just as precisely as 200mm high 3D-plates. Use the system as a plasma cutting system or waterjet cutting system, corresponding extensions are available. In the middle range of the machine (between the footpipes ) you can even process parts up to a height of 850mm (beam shroughl, etc. ) or 3D body up to about 400mm height (at 400mm ...

Specifications / Technical data S-1000/T Portalfraesmaschine / Engraving machine With the T-variant of the High-Z CNC-Fraese you acquire old-fashioned technology with the certain i-tuepfelchen in TUeV-certified quality (Emc). The High-Z/T Fraese is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. Through the ball-circuit spindles used, the High-Z/T achieves fantastic accuracy and an almost unmeasurable reverse play of about 0.01mm. At the same time, high travel speeds of up to approx. 108mm / second ( 6500 mm / minute ) can be achieved. This is how engraving and fraes speeds of up to approx. 4500mm/min can be realized and urgent journeys up to approx. 7000mm/min. Here you can see a video about empty runs with the new high-Z/T 3D CNC machine. This makes this machine series in the industrial sector just as applicable for work ...

Wood Turning Lathe Precision device for professional users, with grey cast iron variable speed control high degree of spindle concentricity Spindle can be fixed all 15° LCD speedometer One hand operation of the tailstock and tool rest with quick-release mechanism Voltage: 230V / 50 Hz Engine power: 735W (S1 100%) Tip height: 160 mm Top width: 510 mm Speed ranges: 250-750 m-1, 550-1650 min-1, 1300-3850 min-1 Spindle stock rotation: 180 degrees Headstock thread: M33 DIN800 Morsekonusaufnahme: MK2 / MT2 Quill stroke: 63 mm Weight: 52 kg Dimensions: 1035 x 305 x 449 mm G & HM-D510F

Specifications / Technical Data S-1000/T CNC-Router / CNC-Engraver With the purchase of the T-variation of High-Z CNC-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T CNC-engraver achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machine you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This cnc-router series is usable in the industrial field as well as for works like engraving, milling, dr ...

Specifications / Technical Data S-720/T CNC-Engraving-Machine / Milling machine / CNC-Router With the purchase of the T-variation of High-Z CNC-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T 3D-cnc-engraver was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc milling machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This cnc-machine series is usable in the industrial ...

Wood Turning Lathe big turning diameter over bed allows the turning of workpieces with large diameter - ideal for turning E.g. plate user friendly adjustable speed Digital speed display comfortable working with hand pad and quick adjustment Spindle/tailstock bore 10 mm Top width: 457 mm Tip height over machine bed: 153 mm 3-stage variable spindle speed: 650-1450 min-1, 1250-2800 min-1, 1600-3800 min-1 Headstock, thread: M33 DIN800 Motor power S1 (100%) / S6: 550W / 770W Mains voltage: 230V Net weight: 33kg G & HM-D460FXL

Equipment / Product data of the CNC-Fraesen Type High-Z/TRex series / Type 1215 Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all axes of HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand edging! speed speed max. 12,000 mm/min Working speed max. approx. 8,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10 microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area 1860 x 1340 mm travel distances: X=1500mm; Y=1200mm; Z= 130 mm contact contactno-point sensors / reference switches / limit switches on all axes Double-secured emergency trigger energy chains for clean cable Total mass with motors : LxWxH approx. 2180 x 1800 x 1420 mm Fra- Sc ...

3D CNC Router T-Rex 1215 / Technical Data : Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all exis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 1860 x 1340 mm Travels: X=1500mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions wi ...

Holzkraft Precision Wood Band Saw HBS 533 SET Product name: Precision wood band saw HBS 533 SET Manufacturer: Holzkraft Item number: 5155303 SET Year of construction: 01/2022 Condition: As good as new technical details: • Dimensions work table (L x W x H): 535 mm x 535 mm x 945 mm • Saw table inclination: -10° to +45° • 2 x suction nozzles • Diameter suction nozzle: 2 x 120 mm • Working table length max.: 685 mm • Work table widening length: 535 mm • Work table widening width: 150 mm • Cutting height max. 90°: 270 mm • Cutting width max. with stop: 474 mm • Cutting width max. without stop: 514 mm • Band saw blade speeds: 850/430 m/min • Band saw length: 3,865 mm • Band saw guide: precision guide at the top and bottom • Weight: approx. 163 kg • incl. band saw set, length 3865 mm, 3 pieces - 1x band saw blade wood 3865 x 10 x 0.5  ...

Bos Machine (BMH) with a Sapiens Wood bosmachines We are a producer of frames, windows and doors and we sell the machine ourselves. The machine has been running in our factory from 2006 to 2022 (16 years). This is a Bos Machine (BMH) with a Sapiens in front of it. The Sapiens is a CNC machine with one robot head and one regular axis. He then proceeds to the tenoning bench (for the crosscut processing). The first shaft is a saw followed by 3 vertical shafts (approx. 500mm long) and behind them two more motors for round edges on the wood. Then he moves on to the milling. The first cutters profile the edge finish and the second cutters profile the inner profile. The first milling cutters consist of 1 milling cutter which profiles and immediately makes the wood thickness, followed by 4 milling motors and then another 5 milling motors for profiling the inner profiling. Technical status: ...

CATALOG NO. 6901 TECHNICAL DATA - max turning length 1200mm - max turning diameter 210mm - max turning diameter with a standard 90mm steady rest - max dimension of square material for turning with automatic feeding 100mm - 3 hydraulic copiers - additional 3 knives on hydraulic pistons (2 pcs) - 4 types of spindle rotation - automatic or manual operation of the machine - headstock spindle motor 9kW - 3kW hydraulic pump motor - diameter of the exhaust connection 90mm - dimensions for transport length/width/height 3700x2100x2000mm - weight about 3000 kg ADVANTAGES – Italian production – automatic hydraulic copier – original DTR documentation – unpainted – used lathe, very good condition Net price: PLN 69900 Net price: 15032EUR Net price calculated according to the exchange rate of 4.65 PLN/EUR (with larger exchange rate fluctuations, the price may cha ...

Wooden flooring line consisting of: Motorized loading roller conveyor Suction cup loader Sliding table saw/panel saw Multi-blade panel saw Tipper Dry or glue-fitted slats Stackers Packaging machines Parcel loader Packaging Automatic pallet unloading strapping machine Camera-guided movements The loading roller conveyor, the stack (max 50 sheets, thickness 8mm) is transported under the suction cup loader, where the panels are picked up and placed on the hopper of the panel saw. Model:TSA 360A The sectioned sheets go on a 90° sideshift and are conveyed by belts over a suction cup feeder. Here, by means of a camera, by means of the black line, they are centered and introduced into the Paul K34G multi-blade panel saw/multi-blade Paul The sectioned slats (n°10 size 130 size 1300x2x20202) go on a 90° sideshift that transports them to an octagonal tilte ...

Used creel, type I75/55 -outdated- Stock number: aga902 Passage: 750 mm Stroke: 550 mm Constructive structure: - Reinforced centre stand made of steel, stress-free cold formed - No cross beam on the incision side thanks to special Stand construction; thus easier saw attachment - Frame beams made of special steel, milled from a single piece - Profile stilts with rolling and cylindrical roller bearings and honing sleeves - Incl. clamp and stop Auto-BV Programmable cutting width adjustment with - Asymmetrical adjustment of the two saw packages (with type 71 with 4 saws, with type 75 with 5 saws per package), with synchronous adjustment of the splitting wedge knives - Control box with PLC control - Pushbutton box with TP operating terminal for convenient program input - Editing program display

1. Dear Ladies and Gentlemen, I refer to your mail to Mr. Schmidt and send you information about the sawmill for sale as requested. I would like to sell the system completely to a buyer and then agree on a package price for the following parts of the system after viewing. The plant is located at the site and is still fully connected. It consists of: 2. 1. Log feeding (cross conveyor, EWD step pusher, block hoist with 2 ejectors) 2. Creel system, Esterer HD 30, with splitting wedge (Arta), outfeed roller conveyor with liftable cross conveyor, and roller conveyors for recutting with lifting cross conveyor to the Costa plant 3. Separation step to the Costa feeding, with infeed roller conveyor to the Costa Mamut cross-cut saw, incl. metal detector 4. Costa Mamut model cross-cut saw, for cutting from 800 to 3000 m, with transfer to Costa double shaft saw "Leone"  ...

Type Overture ES Voltage 230 V (50 Hz) Made in USA Transport dimensions 600x400x500 mm Weight 15 kg

Laser sensor Error detection automatically Shape recognition Laser printer (DIN A4) Number 2 Monochrome cameras PHOTONFOCUS 160 MB Number 2 Barriers + Accessories

Hydraulic gripper for wooden beams with modular suction cups Load capacity kg: 700 Number of suction cups: 16 Dimensions of suction plate mm: 80 x 750 Procedure mm: 8000

Hydraulic wood splitter, functional Details on request

Max Diameter 485mm Min length 1500mm, Max length 5500mm Drive power from the rotor disc 315kw Feeding step separator, feed belt, metal detector Removal Bruks 2x screws 1x 600x6.500mm and 1x 800x9.500mm Wood chip length 25mm Cabinets Year of construction/commissioning 2004 Working hours approx. 12500 hours Capacity 80-100 Qm3/h

Max Diameter 485mm Min length 1500mm, Max length 5500mm Drive power from the rotor disc 315kw Feeding step separator, feed belt, metal detector Removal Bruks 2x screws 1x 600x6.500mm and 1x 800x9.500mm Wood chip length 25mm Cabinets Year of construction/commissioning 2004 Working hours approx. 12500 hours Capacity 80-100 Qm3/h

Max Diameter 485mm Min length 1500mm, Max length 5500mm Drive power from the rotor disc 315kw Feeding step separator, feed belt, metal detector Removal Bruks 2x screws 1x 600x6.500mm and 1x 800x9.500mm Wood chip length 25mm Cabinets Year of construction/commissioning 2004 Working hours approx. 12500 hours Capacity 80-100 Qm3/h

HOT AIR GENERATOR by wood . NEW machines in prompt delivery model F28 , F55CV , F85CV , F120CV Availability : ready in stock ( unless sold ) CE mark : Yes Declaration CE : Yes Instruction Manual ( Yes )

HOT AIR GENERATOR by wood . NEW machines in prompt delivery model F28 , F55CV , F85CV , F120CV Availability : ready in stock ( unless sold ) CE mark : Yes Declaration CE : Yes Instruction Manual ( Yes )

Stencil lathe Manufacturer: Hempel Model: HH 9 Heavy-duty version with oil-hydraulic control Max.: Workpiece length: 900mm Hydraulic sliding supports: 5 pcs.

Copy lathe Brand: Röhrsdorfer model: 83 199 Year of construction: 1987 Workpiece length 100 - 460 mm Kantel dimensions: 20 x 60 mm Equipment: Workpiece magazine Turning knives Template-controlled rotary blade knife, 3x

Disc lathe Lathe for plates, bowls, rings, wheels, etc. Manufacturer: Hempel Model: ERSP / ER/Sp 4 Workpiece diameter: max. 400 mm Workpiece thickness: max. 80 mm

ORDER NO. 6955 TECHNICAL SPECIFICATIONS - loading hopper inlet L x W 1070x710mm - outlet for shredded wood fi 200mm - rotor working width 700mm - main engine 18,5kW - pump motor 1,5kW - number of knives 21pcs - knife size 35x35mm - sieve 50mm - pressure drawer - electric autorewers - dimensions length / width / height 1700x1300x1640mm - weight 1780kg ADVANTAGES – German production – autorewers – pressure drawer – very good condition – used chipper Net price: 67900 PLN Net price: 15089 EUR Net price calculated according to the exchange rate of 4,5 PLN/EUR (with larger fluctuations in the exchange rate, the price may change)

WEIBERT WJ-1200 Lathe Distance between centers 1200mm Center height 215mm Spindle thread M33 Spindle speeds 500/1000/2000/2800 Motor output power 1.5KW Face plate Hand rest concurrent grain tip 400V and 230V G&WJ-1200 Net price 1639,-€ with VAT 1950,-€ Option: spindle speeds infinitely variable net 790,-€

Weima WL 6 Hacker Hopper size / feed opening (mm): 800 x 1200 Rotor diameter (mm): 368 Rotor length (mm): 800 Rotor speed (rpm): 60 - 100 Drive power (kW): 22 / 30 / 37 Number of knives (pcs.): 23 / 42 2 row of knives Weight (Kg approx.): 2000 Suction nozzle diameter (mm): 200 Screen perforation (mm): 10 - 40 G&WE-WL6/18,5

DBK 1300 Lathe Center height above machine bed: 220 mm Distance between centers: 1300 mm Center height over palm rest support: 160 mm Spindle speed: 0 to 3000 rpm Headstock, thread holder: M33 Tailstock Morse cone mount: MK2 Pinolenweg/tail spindle travel: 100 mm Motor power S1 (100%) / S6: 1.1kW/1.5kW Mains voltage: 230 V or 400 V Net weight: 160 kg G&HM-DBK1300

Brand: Sicar Type: Wood milling bench + extraction Model: SF70 Chassis number: BO400062003 Construction year: 2003 Weight: 0,28 tons Length mm: 2500 Width mm: 1000 Height mm: 1700 Transport size L x W x H: 2,5 x 1,0 x 1,7 Condition machine : Good

Trolley bajler zembrod OBX 3 Crane width 3m

Weibert DB 460XL Vario Lathe Diameter max. 305mm Center Size x Height: 460 x 155mm Spindle head thread M33 x 3.5 MK2 3 speeds: 650-1430, 1240-2790, 1600-3800 rpm Electronically variable Rotating grain tip Four-pronged driver Swivel steel support 150mm, 300mm Clamping washer 145mm Quill adjustment: 55mm Motor 550W 230V 50Hz Dimensions (LxWxH): 900 x 340 x 410mm Net weight approx. 38kg G&STÜ-5920462

OMEC TA185 crosscut saw Maximum cutting height 180mm Maximum cutting width 900mm Saw blade diameter 550mm Pneumatic material clamping Pneumatic saw passage Saw control with two buttons 7.5kw main motor 2x roller tables length 160cm each CE Certified White Paper

SECOND-HAND VERTICAL HYDRAULIC CLAMP FOR WOOD PANELS STROMAB MOD. SL1 - CE RULES - volt. 400/50 - year 2009 - 3000x1300mm

Rudnick&Enners Drum Chipper Type: RE-TH 250/650/5 Main motor: 75 kW Inlet width: 700 mm Inlet height 300 mm Feed rollers: 3 bottom, 2 top with control cabinet and metal detector

SPECIFICATIONS: Dimensions of the work table mm: 2500 x 1300 Number of pistons: 4 Diameter Ø 90 mm Piston stroke mm: 470 Complete with intermediate plate Operation with water

Hacker Lindner T 650/220-2 with Virborinnen with scraper conveyor with metal detector 55kw...